have fun

mcu-cec-bedroom.yaml

@@ -0,0 +1,166 @@
+substitutions:
+  device: cec-bedroom
+  name: Bedroom TV
+  comment: "DEV"
+  
+esphome:
+  name: mcu-${device}
+  comment: ${comment}
+
+esp32:
+  board: m5stack-atom
+  framework:
+    type: arduino
+    # type: esp-idf
+
+external_components:
+  # - source: github://pr#3017
+  #   components: [hdmi_cec]
+  #   refresh: 1h
+  - source: github://Palakis/esphome-hdmi-cec
+    refresh: 1h
+packages:
+  common: !include common/common.yaml
+
+debug:
+
+time:
+  - platform: homeassistant
+    id: ha_time
+    timezone: Europe/Bratislava
+
+i2c:
+  # - id: i2c0
+  sda: 32
+  scl: 33
+  scan: true #false
+  frequency: 100kHz
+  # - id: i2c1
+  # sda: 25
+  # scl: 22
+  # scan: true #false
+
+uart:
+  - id: uart_distance
+    tx_pin: 25
+    rx_pin: 22
+    baud_rate: 9600
+
+sensor:
+ - platform: a02yyuw
+   uart_id: uart_distance
+   name: 'Distance'
+   accuracy_decimals: 2
+   unit_of_measurement: cm
+
+binary_sensor:
+  - platform: gpio
+    name: ${name} Button
+    pin:
+      number: 39
+      inverted: true
+
+light:
+  - platform: neopixelbus
+    type: GRB
+    pin: 27
+    variant: WS2812
+    num_leds: 1
+    name: "${name} LED"
+    id: neo
+    effects:
+      # Use default parameters:
+      - random:
+      # Customize parameters
+      - random:
+          name: "My Slow Random Effect"
+          transition_length: 30s
+          update_interval: 30s
+      - random:
+          name: "My Fast Random Effect"
+          transition_length: 4s
+          update_interval: 5s
+      - strobe:
+      - strobe:
+          name: Strobe Effect With Custom Values
+          colors:
+            - state: True
+              brightness: 100%
+              red: 100%
+              green: 90%
+              blue: 0%
+              duration: 500ms
+            - state: False
+              duration: 250ms
+            - state: True
+              brightness: 100%
+              red: 0%
+              green: 100%
+              blue: 0%
+              duration: 500ms
+      - flicker:
+      - flicker:
+          name: Flicker Effect With Custom Values
+          alpha: 95%
+          intensity: 1.5%
+      - addressable_rainbow:
+      - addressable_rainbow:
+          name: Rainbow Effect With Custom Values
+          speed: 10
+          width: 50
+      - addressable_scan:
+      - addressable_scan:
+          name: Scan Effect With Custom Values
+          move_interval: 100ms
+
+hdmi_cec:
+  # The initial logical address -- corresponds to device type. This may be
+  # reassigned if there are other devices of the same type on the CEC bus.
+  address: 0x05 # Audio system
+  # Promiscuous mode can be enabled to allow receiving messages not intended for us
+  promiscuous_mode: false
+  # Typically the physical address is discovered based on the point-to-point
+  # topology of the HDMI connections using the DDC line. We don't have access
+  # to that so we just hardcode a physical address.
+  physical_address: 0x4000
+  pin: 26
+  on_message:
+    - opcode: 0xC3 # Request ARC start
+      then:
+        - hdmi_cec.send: # Report ARC started
+            destination: 0x0
+            data: [ 0xC1 ]
+    - opcode: 0x70 # System audio mode request
+      then:
+        - hdmi_cec.send:
+            destination: 0x0
+            data: [ 0x72, 0x01 ]
+    - opcode: 0x71 # Give audio status
+      then:
+        - hdmi_cec.send:
+            destination: 0x0
+            data: [ 0x7A, 0x7F ]
+    - opcode: 0x7D # Give audio system mode status
+      then:
+        - hdmi_cec.send:
+            destination: 0x0
+            data: [ 0x7E, 0x01 ]
+    - opcode: 0x46 # Give OSD name
+      then:
+        - hdmi_cec.send:
+            destination: 0x0
+            data: [0x47, 0x65, 0x73, 0x70, 0x68, 0x6F, 0x6D, 0x65] # esphome
+    - opcode: 0x8C # Give device Vendor ID
+      then:
+        - hdmi_cec.send:
+            destination: 0x0
+            data: [0x87, 0x00, 0x13, 0x37]
+    - data: [0x44, 0x41] # User control pressed: volume up
+      then:
+        - logger.log: "Volume up"
+    - data: [0x44, 0x42] # User control pressed: volume down
+      then:
+        - logger.log: "Volume down"
+    - data: [0x44, 0x43] # User control pressed: volume mute
+      then:
+        - logger.log: "Volume mute"