all esp32: disable wifi power saving

common/wifi.yaml

@@ -9,3 +9,4 @@ wifi:
   enable_btm: true
   enable_rrm: true
   min_auth_mode: WPA3
+  power_save_mode: none

mcu-basement-2.yaml

@@ -22,6 +22,7 @@ esphome:
 
 esp8266:
   board: esp01_1m
+  toolchain: arduino
 
 packages:
   common: !include common/common_esp8266.yaml

mcu-basement.yaml

@@ -21,6 +21,7 @@ esphome:
 
 esp8266:
   board: esp01_1m
+  toolchain: arduino
 
 packages:
   common: !include common/common_esp8266.yaml

mcu-fireplace.yaml

@@ -37,56 +37,26 @@ esp32:
       flash_chip: gd
     type: esp-idf
 
-external_components:
-  # - source: github://pr#12717
-  #   components: [ds248x]
-  #   refresh: 1h
-  - source: github://pr#13534
-    components: [ds2482, ds2484, ds248x_base]
-    refresh: 1h
-
 packages:
   common: !include common/common.yaml
   ipv6_only: !include common/ipv6_only.yaml
   status_led: !include common/status_led_atom.yaml
 
-
 i2c:
-  # - id: i2c0
-  #   sda: 26
-  #   scl: 32
-  #   scan: true #false
-  # - id: i2c1
   sda: 25
   scl: 21
   scan: true #false
 
-# ds248x:
+ds248x:
-#   # i2c_id: i2c_main
+  id: ds2484_module
-#   address: 0x18 # should be the default
+  type: ds2482-100
-#   # sleep_pin: 32 # remove if not needed, if set the ds248x sleeps when no transaction is in progress
+  address: 0x18
-#   active_pullup: true # adds a active pullup which should improve signal integrity
+  active_pullup: true
-#   strong_pullup: false # enables a strong pullup used to provide the needed current for temperature reading without vcc connected
-#   bus_sleep: true # power down the bus when no transaction is in progres
-
-# one_wire:
-#   id: one_wire_bus
-#   platform: ds2484
-#   active_pullup: true
-
-# ds248x:
-#   id: ds2484_module
-#   address: 0x18
-
-# one_wire:
-#   - platform: ds248x
-#     ds248x_id: ds2484_module
-#     id: one_wire_bus
 
 one_wire:
+  - platform: ds248x
+    ds248x_id: ds2484_module
     id: one_wire_bus
-  platform: ds2482
-  active_pullup: true
 
 pca9554:
   - id: pca9554_module
@@ -133,16 +103,6 @@ sensor:
     # index: 0
     name: Temperature
     id: 'heating_fireplace_temperature'
-#   - platform: dht
-#     pin: 14
-#     temperature:
-#       name: "Kitchen Temperature"
-#       id: 'kitchen_temperature'
-#     humidity:
-#       name: "Kitchen Humidity"
-#       id: 'kitchen_humidity'
-#     update_interval: 60s
-#     model: si7021
 
 bluetooth_proxy:
   active: true

mcu-heater.yaml

@@ -47,26 +47,11 @@ esp32:
       flash_chip: gd
     type: esp-idf
 
-external_components:
-  # - source: github://pr#12717
-  #   components: [ds248x]
-  #   refresh: 1h
-  - source: github://pr#13534
-    components: [ds2482, ds2484, ds248x_base]
-    refresh: 1h
-
 packages:
   common: !include common/common.yaml
   ipv6_only: !include common/ipv6_only.yaml
   status_led: !include common/status_led_atom.yaml
 
-#logger:
-#  level: VERBOSE
-#  logs:
-#    dallas.component: ERROR
-#    uart.component: ERROR
-#    i2c.component: VERBOSE
-
 # Heating / Hot water Controller
 # temp_1: Solar Collector
 # temp_2: Cylinder Bottom (solar)
@@ -170,36 +155,22 @@ climate:
       default_target_temperature_high: 40 °C
 
 i2c:
-  # - id: i2c0
+
-  # sda: 26
-  # scl: 32
-  # scan: true #false
-  # - id: i2c1
   sda: 25
   scl: 21
   scan: true #false
 
-# one_wire:
-#   id: one_wire_bus
-#   # i2c_id: i2c_main
-#   platform: ds2484
-#   active_pullup: true
 
-# ds248x:
+ds248x:
-#   id: ds2484_module
+  id: ds2482_module
-#   address: 0x18
+  type: ds2482-100
-#   active_pullup: true
+  address: 0x18
-
+  active_pullup: true
-# one_wire:
-#   - platform: ds248x
-#     ds248x_id: ds2484_module
-#     id: one_wire_bus
 
 one_wire:
+  - platform: ds248x
+    ds248x_id: ds2482_module
     id: one_wire_bus
-  # i2c_id: i2c_main
-  platform: ds2482
-  active_pullup: true
 
 modbus:
   uart_id: uart_modbus

mcu-rf433.yaml

@@ -18,6 +18,7 @@ esphome:
 
 esp8266:
   board: esp01_1m
+  toolchain: arduino
 
 packages:
   common: !include common/common_esp8266.yaml

mcu-socket-01.yaml

@@ -26,6 +26,7 @@ esphome:
 
 esp8266:
   board: esp01_1m
+  toolchain: arduino
 
 packages:
   common: !include common/common_esp8266.yaml

mcu-socket-02.yaml

@@ -26,6 +26,7 @@ esphome:
 
 esp8266:
   board: esp01_1m
+  toolchain: arduino
 
 packages:
   common: !include common/common_esp8266.yaml

mcu-socket-03.yaml

@@ -30,8 +30,10 @@ esphome:
   friendly_name: ${name}
   area: ${area}
   comment: ${comment}
+
 esp8266:
   board: esp01_1m
+  toolchain: arduino
 
 packages:
   common: !include common/common_esp8266.yaml

mcu-staircase-light.yaml

@@ -17,6 +17,7 @@ esphome:
 
 esp8266:
   board: esp01_1m
+  toolchain: arduino
 
 packages:
   common: !include common/common_esp8266.yaml

mcu-tv-light.yaml

@@ -31,6 +31,7 @@ esphome:
 
 esp8266:
   board: esp8285
+  toolchain: arduino
 
 packages:
   common: !include common/common_esp8266.yaml

mcu-waterproof-socket.yaml

@@ -20,6 +20,7 @@ esphome:
 
 esp8266:
   board: esp01_1m
+  toolchain: arduino
 
 packages:
   common: !include common/common_esp8266.yaml