---
substitutions:
  device: fireplace
  name: Heating Fireplace
  area: Living Room & Kitchen
  comment: "${area}, Fireplace | Fireplace monitoring for heating"

esphome:
  name: mcu-${device}
  friendly_name: ${name}
  area: ${area}
  comment: ${comment}

esp32:
  variant: esp32
  framework:
    type: esp-idf

external_components:
  # - source: github://pr#12717
  #   components: [ds248x]
  #   refresh: 1h
  - source: github://pr#13534
    components: [ds2482, ds2484, ds248x_base]
    refresh: 1h

packages:
  common: !include common/common.yaml


# PINOUTS: M5ATOM+Atom Hub Switch
# IR        G12
# NEO       G27 1x
# BUTTON    G39
# I2C0 SDA  G26 - white
# I2C0 SCL  G32
# I2C1 SDA  G25 - red
# I2C1 SCL  G21
# UART0 RX  G3
# UART0 TX  G1
# RS485 Rx  G33
# RS485 Tx  G23
# Relay1    G22
# Relay2    G19

time:
  - platform: homeassistant
    id: ha_time
    timezone: Europe/Bratislava

i2c:
  # - id: i2c0
  #   sda: 26
  #   scl: 32
  #   scan: true #false
  # - id: i2c1
  sda: 25
  scl: 21
  scan: true #false

# ds248x:
#   # i2c_id: i2c_main
#   address: 0x18 # should be the default
#   # sleep_pin: 32 # remove if not needed, if set the ds248x sleeps when no transaction is in progress
#   active_pullup: true # adds a active pullup which should improve signal integrity
#   strong_pullup: false # enables a strong pullup used to provide the needed current for temperature reading without vcc connected
#   bus_sleep: true # power down the bus when no transaction is in progres

# one_wire:
#   id: one_wire_bus
#   platform: ds2484
#   active_pullup: true

# ds248x:
#   id: ds2484_module
#   address: 0x18

# one_wire:
#   - platform: ds248x
#     ds248x_id: ds2484_module
#     id: one_wire_bus

one_wire:
  id: one_wire_bus
  platform: ds2482
  active_pullup: true

pca9554:
  - id: pca9554_module
    address: 0x27

# modbus:
#   uart_id: uart1

# uart:
#   - id: uart1
#     rx_pin: 33
#     tx_pin: 32
#     baud_rate: 9600
#     stop_bits: 2

binary_sensor:
  - platform: gpio
    name: Status Button
    filters:
      - invert:
    pin: 39
  - platform: template
    name: Fire
    lambda: |-
      if (id(heating_fireplace_temperature).state > 37.5) {
        return true;
      } else {
        return false;
      }
  - platform: gpio
    name: Pump
    id: off_peak_status
    pin:
      pca9554: pca9554_module
      number: 0
    filters:
      - delayed_on: 300ms
      - delayed_off: 300ms

sensor:
  # - platform: ds248x
  - platform: dallas_temp
    address: 0x6203168B32A7FF28
    # index: 0
    name: Temperature
    id: 'heating_fireplace_temperature'
#   - platform: dht
#     pin: 14
#     temperature:
#       name: "Kitchen Temperature"
#       id: 'kitchen_temperature'
#     humidity:
#       name: "Kitchen Humidity"
#       id: 'kitchen_humidity'
#     update_interval: 60s
#     model: si7021

bluetooth_proxy:
  active: true