Install yamllint with pip instead of ibiqlik/action-yamllint, which expects
it preinstalled like on GitHub's runner, and pip install with
--ignore-installed so pip doesn't try to remove Debian's packages.
allow_plaintext_upload lets the uploader give a device that doesn't encrypt
yet its one migration install. Remove it together with the password once
every device has been updated (the uploader says so).
Values come from ESPHome's own hint in the log of each online device
("Set flash_chip: ... to save IRAM"). Devices that were off got the value of
an identical board (ESP32-PICO-D4 ATOM/Stamp Pico: gd, JC3248W535: generic,
POW Elite: gd), marked as not read from the device.
- actions/checkout@v7 and tj-actions/changed-files@v47 (Node 20 is deprecated)
- PIP_BREAK_SYSTEM_PACKAGES for Gitea's runner image (externally-managed Python)
- untrack common/.esphome (a gitlink with no submodule mapping) and ignore
.esphome/ in every directory
common/status_led_atom.yaml puts common/status_led.yaml on the ATOM Lite's
own RGB LED (G27, 64 RMT symbols to leave room for IR/RF). echo-1 uses its
existing LED light.
Red blink without network, orange without an API client, purple on a
component error, blue blink during OTA, green when things are back to
normal, then the light returns to its previous state.
echo uses it on the gateway LED ring; drop its status_led on GPIO23,
which never worked because the ledc output owns that pin.
common/nspanel_popup.yaml shows a popupNotify page during OTA (written straight
to the display uart, since OTA blocks the loop that sends the component's
queued commands) and a device info popup (version, build time, IPs) from the
Info button on the new last card or the show_info API action. The OTA gets
id ota_esphome to extend it. Also documents the NSPanel pinout.
- mipi_rgb GUITION-4848S040 model, ST7701S init over SPI (48/47)
- GT911 touch mirrored like the image, backlight on GPIO38
- clock and status pages (status until Home Assistant connects),
same navigation bar as the other LVGL displays
- IPv6-only network
mcu-lvgl (CYD 4.3"):
- normalized: rpi_dpi_rgb -> mipi_rgb (ESP32-8048S050 pins/timing, pclk
12.5 MHz), GT911 touch added, platformio_options and default CPU
frequency dropped, demo meters and duplicate uptime sensors removed
- pages: clock, status (logo, WiFi, IPv6 first, HA, version, uptime);
status page shown until Home Assistant connects
- same navigation bar and theme as mcu-lvgl-trainer
mcu-lvgl-trainer:
- status lines colored like on the other displays (connected green,
waiting orange, details gray), stacked in a flex column
- stopwatch format warning fixed
Same boot screen as on the other displays: "Made for ESPHome" logo,
name, WiFi with signal, IPv6 addresses first (link-local skipped),
Home Assistant state, ESPHome version and uptime.
- common/wifi.yaml: the network gets id wifi_iot, so devices can
override it with '!extend wifi_iot'
- common/ipv6_only.yaml: add-on package next to any common package;
switches to the IPv6-only SSID, wifi ipv6_only (SLAAC, no DHCPv4,
esphome/esphome#19750 as external component until merged) and
min_ipv6_addr_count: 1
- mcu-lvgl-trainer, mcu-nspanel-dev, mcu-rfid-reader, mcu-stackchan,
mcu-tft moved to the IPv6-only network
Inactive display dim follows the sun (5 % by day, off after dusk at
-6 degrees) and stays at 5 % while light.office_j_lights is on.
Re-applied on time sync, at dawn/dusk and when the lights change.
- touch: drop calibration/transform, the driver defaults to the native
320x480 panel and LVGL rotates touch points itself (taps were rotated
by 90 degrees)
- pages: clock (default), basement lights with brightness and color
temperature for the exercise room (sliders hidden while it is off),
training start/stop, fan off/50-100 %, stopwatch, status screen with
"Made for ESPHome" logo and IPv6 first
- light attributes read as text, 'None' while off is skipped
- unused fonts, colors and leftovers removed; ext_uart kept for a
future ANT+ bridge
- status screen logo replaced by the official "Made for ESPHome" badge,
the plain ESPHome logo is not meant for third-party devices
- status screen shows one global IPv6 and one IPv4 address (link-local
skipped) instead of the IPv4 sensor value
Rewrite of the old config on the core ESPHome components (it8951, gt911,
bm8563, sht3xd):
- USB: always on, forecast screen redrawn every 15 min, forecast
refreshed every hour and when Home Assistant connects
- battery: BM8563 timer wakes the board every 15 min (off 1:00-5:00),
it draws the stored forecast and cuts power; WiFi only when the
forecast is older than 6 h
- mode detected by trying to power off; battery voltage drop on USB
triggers the battery cycle
- hourly forecast via weather.get_forecasts, 48 h kept in the FM24C02
EEPROM (include/m5paper_weather.h)
- OTA image confirmed before power-off, battery wake-ups are shorter
than boot_is_good_after
- status screen with "Made for ESPHome" logo, IPv6 addresses first
Move the homeassistant time platform (id ha_time) into all common
packages. Devices with custom triggers now use '!extend ha_time';
plain duplicate time blocks are removed. mcu-lvgl's unused time_comp
is unified to ha_time.
- Winamp style spectrum analyzer instead of the face while music plays,
using audio_spectrum from randybb/esphome-components
- head touch: tap starts the assistant, stroking shows an in-love face;
SI12T sensitivity raised so the pads actually trigger
- battery (AXP2101) and wifi indicators, ear icon while listening
Voice assistant satellite with animated face on the CoreS3 display:
- power rails, IO expander resets and servo power as in the M5 BSP
- mic and speaker share one I2S bus, so the mic is released before playback
- AW88298 volume limited to the audible range (0.5-1.0)
- partial display redraws, status screen until Home Assistant connects
- battery and wifi indicators, listening icon
- camera converted to JPEG on demand, no periodic frames
Switch all NSPanels from the MQTT + AppDaemon based
esphome-nspanel-lovelace-ui to the native component
(randybb/esphome-nspanel-lovelace-native, ref: devices).
Cards and screensaver are now configured directly in ESPHome,
removing the dependency on MQTT and AppDaemon.
qspi_dbi is deprecated in favor of mipi_spi. Also fixes
mcu-lvgl-trainer's LVGL rotation (must be set on the lvgl component,
not the display, when LVGL is in use) and its deprecated
publish_initial_state -> trigger_on_initial_state. brightness is
dropped since mipi_spi only supports it for AMOLED panels and both
devices already control backlight separately.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
ESPHome renamed the esp32_rmt_led_strip platform's rgb_order option to
channel_colors; update the remaining devices using it.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
The i2s_audio media_player platform was removed; rebuild the audio
pipeline like mcu-echo.yaml with an i2s_audio speaker feeding a
mixer, so media playback, TTS announcements, and rtttl beeps all
share the one physical DAC output without conflicting. Also uses
format: NONE instead of the deprecated codec_support_enabled.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
The single on_multi_click FSM mixed an unbounded "at least 1500ms"
pattern with two bounded blink patterns, which made Open detection
unreliable. Split into two binary_sensor entries sharing the same
pin: a filter-based one for steady Open/Closed, and a dedicated
on_multi_click for the Opening/Closing blink patterns.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
register_count is derived from value_type now; drop the now-redundant
register_count: 1 on the temp/humidity sensors, and replace the
Solar Pressure sensor's register_count: 2 (its device always returns
2 registers per read) with a hidden padding sensor on the next
register using reuse_previous_range: true, per the new
modbus_controller range-grouping mechanism.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
ili9xxx is being phased out in favor of the unified mipi_spi driver;
model TFT 2.4 maps to the ILI9341 chip it was already using.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Adds a UART-based Modbus link plus scripts to toggle channel 1 on the
n4dig08 relay module, and calls relay_module.setup() before each
irrigation switch action.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Move rx/tx off the shared gdo0 pin (21) onto dedicated pins, drop the
now-unneeded allow_other_uses/gdo0_pin workarounds, and align tx/rx
frequency to 433.92MHz.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Reflects what the device actually controls; renames the entity/id
(blower_auto -> aerator_auto) and display names accordingly.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
ESPHome renamed the esp32_rmt_led_strip platform's rgb_order option to
channel_colors; update all devices using it.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
ESPHome renamed the api component's services/service keys to
actions/action; update all devices using the old names.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
It's generated/local state from ESPHome Device Builder that changes
constantly and doesn't belong in version control.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
randy
