Change old style platform on last 5 devices

common/common.yaml

@@ -2,7 +2,8 @@
 <<: !include wifi.yaml
 <<: !include api.yaml
 <<: !include ota.yaml
-<<: !include logger.yaml
+# <<: !include logger.yaml
+<<: !include logger_debug.yaml
 
 binary_sensor:
   - <<: !include binary_sensor/status.yaml
@@ -18,7 +19,9 @@ sensor:
   - <<: !include sensor/wifi_signal.yaml
 
 text_sensor:
+  - <<: !include text_sensor/debug.yaml
   - <<: !include text_sensor/version.yaml
+  # - <<: !include text_sensor/uptime.yaml
   - <<: !include text_sensor/wifi_info.yaml
 
 network:

common/common_esp8266.yaml

@@ -2,7 +2,8 @@
 <<: !include wifi_esp8266.yaml
 <<: !include api.yaml
 <<: !include ota.yaml
-<<: !include logger.yaml
+# <<: !include logger.yaml
+<<: !include logger_debug.yaml
 
 binary_sensor:
   - <<: !include binary_sensor/status.yaml
@@ -18,9 +19,9 @@ sensor:
   - <<: !include sensor/wifi_signal.yaml
 
 text_sensor:
+  - <<: !include text_sensor/debug.yaml
   - <<: !include text_sensor/version.yaml
   - <<: !include text_sensor/wifi_info.yaml
 
 network:
-  enable_ipv6: true
+  enable_ipv6: true
-#   min_ipv6_addr_count: 2

common/text_sensor/uptime.yaml

@@ -0,0 +1,3 @@
+---
+platform: uptime
+name: ${name} Uptime

mcu-air-office-r.yaml

@@ -13,8 +13,8 @@ esp32:
   # board: m5stamp-pico
   framework:
     type: esp-idf
-    version: 5.1.2
+    # version: 5.2.1
-    platform_version: 6.6.0
+    # platform_version: 6.6.0
 
 external_components:
   - source: components
@@ -58,7 +58,7 @@ light:
     rgb_order: GRB
     pin: 27
     num_leds: 1
-    rmt_channel: 0
+    # rmt_channel: 0
     chipset: ws2812
     restore_mode: ALWAYS_OFF
   - platform: esp32_rmt_led_strip
@@ -67,7 +67,7 @@ light:
     rgb_order: GRB
     pin: 25
     num_leds: 7
-    rmt_channel: 1
+    # rmt_channel: 1
     chipset: ws2812
     restore_mode: ALWAYS_OFF
     effects:

mcu-basement-2.yaml

@@ -7,9 +7,9 @@ substitutions:
 esphome:
   name: mcu-${device}
   comment: ${comment}
-  platform: ESP8266
-  board: esp01_1m
 
+esp8266:
+  board: esp01_1m
 
 packages:
   common: !include common/common_esp8266.yaml

mcu-basement.yaml

@@ -6,7 +6,8 @@ substitutions:
 esphome:
   name: mcu-${device}
   comment: ${comment}
-  platform: ESP8266
+
+esp8266:
   board: esp01_1m
 
 packages:

mcu-bedroom-lamp-left.yaml

@@ -14,8 +14,8 @@ esp32:
     type: esp-idf
     sdkconfig_options:
       CONFIG_FREERTOS_UNICORE: y
-      ESP_MAC_IGNORE_MAC_CRC_ERROR: y
     advanced:
+      ignore_efuse_custom_mac: true
       ignore_efuse_mac_crc: true
 
 external_components:

mcu-bedroom-lamp-right.yaml

@@ -15,6 +15,7 @@ esp32:
     sdkconfig_options:
       CONFIG_FREERTOS_UNICORE: y
     advanced:
+      ignore_efuse_custom_mac: true
       ignore_efuse_mac_crc: true
 
 external_components:

mcu-c6-test-1.yaml

@@ -0,0 +1,115 @@
+substitutions:
+  device: c6-test-1
+  name: C6 TEST 1
+  comment: "DEV"
+  
+esphome:
+  name: mcu-${device}
+  comment: ${comment}
+  # platformio_options:
+  #   board_build.flash_mode: dio
+  on_loop:
+    then:
+      lambda: |-
+        static uint32_t last_state = 0;
+        auto state = App.get_app_state();
+        if (state != last_state) {
+          if (state & STATUS_LED_ERROR) {
+            auto call = id(led).turn_on();
+            call.set_effect("ERROR");
+            call.perform();
+          } else if (state & STATUS_LED_WARNING) {
+            auto call = id(led).turn_on();
+            call.set_effect("BOOT");
+            call.perform();
+          } else {
+            //auto call = id(led).turn_off();
+            //call.perform();
+            auto call = id(led).turn_on();
+            call.set_effect("BEACON");
+            call.perform();
+          }
+          last_state = state;
+        }
+
+esp32:
+  board: esp32-c6-devkitc-1
+  variant: esp32c6
+  flash_size: 16MB
+  framework:
+    type: esp-idf
+    version: 5.2.1
+    platform_version: 6.6.0
+
+logger:
+  hardware_uart: USB_SERIAL_JTAG
+  logs:
+    component: ERROR 
+
+# web_server:
+#   port: 80
+#   version: 3
+
+light:
+  - platform: esp32_rmt_led_strip
+    name: "${name} LED"
+    id: led
+    rgb_order: GRB
+    pin: 8
+    num_leds: 1
+    # rmt_channel: 0
+    chipset: sk6812 #ws2812
+    restore_mode: ALWAYS_OFF
+    effects:
+      - strobe:
+          name: "BEACON"
+          colors:
+            - state: true
+              red: 0%
+              green: 0%
+              blue: 50%
+              duration: 200ms
+            - state: false
+              duration: 200ms
+            - state: true
+              red: 0%
+              green: 0%
+              blue: 50%
+              duration: 200ms
+            - state: false
+              duration: 10s
+      - lambda:
+          name: "ERROR"
+          update_interval: 0.5s
+          lambda: |-
+            static bool state = false;
+            auto call = id(led).turn_on();
+            call.set_transition_length(500);
+            call.set_rgb(1, 0, 0);
+            if (!state) {
+              call.set_brightness(1);
+            } else {
+              // If using 0, it freaks Home Assistant UI.
+              call.set_brightness(0.01);
+            }
+            call.perform();
+            state = !state;
+      - lambda:
+          name: "BOOT"
+          update_interval: 0.5s
+          lambda: |-
+            static bool state = false;
+            auto call = id(led).turn_on();
+            call.set_transition_length(500);
+            call.set_rgb(0, 1, 0);
+            if (!state) {
+              call.set_brightness(1);
+            } else {
+              // If using 0, it freaks Home Assistant UI.
+              call.set_brightness(0.01);
+            }
+            call.perform();
+            state = !state;
+
+packages:
+  common: !include common/common.yaml

mcu-c6-test-2.yaml

@@ -0,0 +1,115 @@
+substitutions:
+  device: c6-test-2
+  name: C6 TEST 2
+  comment: "DEV"
+  
+esphome:
+  name: mcu-${device}
+  comment: ${comment}
+  # platformio_options:
+  #   board_build.flash_mode: dio
+  on_loop:
+    then:
+      lambda: |-
+        static uint32_t last_state = 0;
+        auto state = App.get_app_state();
+        if (state != last_state) {
+          if (state & STATUS_LED_ERROR) {
+            auto call = id(led).turn_on();
+            call.set_effect("ERROR");
+            call.perform();
+          } else if (state & STATUS_LED_WARNING) {
+            auto call = id(led).turn_on();
+            call.set_effect("BOOT");
+            call.perform();
+          } else {
+            //auto call = id(led).turn_off();
+            //call.perform();
+            auto call = id(led).turn_on();
+            call.set_effect("BEACON");
+            call.perform();
+          }
+          last_state = state;
+        }
+
+esp32:
+  board: esp32-c6-devkitc-1
+  variant: esp32c6
+  flash_size: 16MB
+  framework:
+    type: esp-idf
+    version: 5.2.1
+    platform_version: 6.6.0
+
+logger:
+  hardware_uart: USB_SERIAL_JTAG
+  logs:
+    component: ERROR 
+
+# web_server:
+#   port: 80
+#   version: 3
+
+light:
+  - platform: esp32_rmt_led_strip
+    name: "${name} LED"
+    id: led
+    rgb_order: GRB
+    pin: 8
+    num_leds: 1
+    # rmt_channel: 0
+    chipset: sk6812 #ws2812
+    restore_mode: ALWAYS_OFF
+    effects:
+      - strobe:
+          name: "BEACON"
+          colors:
+            - state: true
+              red: 0%
+              green: 0%
+              blue: 50%
+              duration: 200ms
+            - state: false
+              duration: 200ms
+            - state: true
+              red: 0%
+              green: 0%
+              blue: 50%
+              duration: 200ms
+            - state: false
+              duration: 10s
+      - lambda:
+          name: "ERROR"
+          update_interval: 0.5s
+          lambda: |-
+            static bool state = false;
+            auto call = id(led).turn_on();
+            call.set_transition_length(500);
+            call.set_rgb(1, 0, 0);
+            if (!state) {
+              call.set_brightness(1);
+            } else {
+              // If using 0, it freaks Home Assistant UI.
+              call.set_brightness(0.01);
+            }
+            call.perform();
+            state = !state;
+      - lambda:
+          name: "BOOT"
+          update_interval: 0.5s
+          lambda: |-
+            static bool state = false;
+            auto call = id(led).turn_on();
+            call.set_transition_length(500);
+            call.set_rgb(0, 1, 0);
+            if (!state) {
+              call.set_brightness(1);
+            } else {
+              // If using 0, it freaks Home Assistant UI.
+              call.set_brightness(0.01);
+            }
+            call.perform();
+            state = !state;
+
+packages:
+  common: !include common/common.yaml

mcu-cam-1.yaml

@@ -10,10 +10,10 @@ esphome:
 esp32:
   board: esp32cam
   framework:
-    type: arduino
+    # type: arduino
-    # type: esp-idf
+    type: esp-idf
-    version: 2.0.14
+    # version: 2.0.14
-    platform_version: 6.5.0
+    # platform_version: 6.5.0
 
 packages:
   common: !include common/common.yaml

mcu-can-node-1.yaml

@@ -0,0 +1,91 @@
+substitutions:
+  device: can-node-1
+  name: CAN Node 1
+  comment: "DEV"
+  
+esphome:
+  name: mcu-${device}
+  comment: ${comment}
+
+esp32:
+  board: esp32dev
+  framework:
+    # type: arduino
+    type: esp-idf
+    # version: 5.1.2
+    # platform_version: 6.5.0
+
+external_components:
+  - source: github://mrk-its/esphome-canopen@dev
+    refresh: 1h
+
+packages:
+  common: !include common/common.yaml
+  
+canbus:
+  - platform: esp32_can
+    id: can_bus
+    rx_pin: 22
+    tx_pin: 23
+    can_id: 0
+    bit_rate: 125kbps
+
+canopen:
+  id: can_gate
+  canbus_id: can_bus
+  node_id: 1
+  entities:
+    - id: boot
+      index: 1
+      tpdo: 0
+    - id: blue_led
+      index: 2
+      tpdo: 0
+    - id: uptime_sensor
+      index: 3
+      tpdo: 0
+    - id: cover1
+      index: 4
+      tpdo: 1
+    # - id: cover2
+    #   index: 5
+    #   tpdo: 1
+
+sensor:
+  - platform: uptime
+    id: uptime_sensor
+    name: "${name} Uptime"
+    update_interval: 5sec
+    internal: true
+
+binary_sensor:
+  - platform: gpio
+    name: "${name} Boot"
+    id: boot
+    internal: true
+    pin:
+      number: 0
+      inverted: true
+
+switch:
+  - platform: gpio
+    name: "${name} Led"
+    id: blue_led
+    internal: true
+    pin: 2
+
+cover:
+  - platform: time_based
+    name: "${name} Cover"
+    id: cover1
+    internal: true
+    device_class: shutter
+    has_built_in_endstop: true
+    open_action:
+      - logger.log: open_action
+    open_duration: 10s
+    close_action:
+      - logger.log: close_action
+    close_duration: 10s
+    stop_action:
+      - logger.log: stop_action

mcu-can-node-2.yaml

@@ -0,0 +1,91 @@
+substitutions:
+  device: can-node-2
+  name: CAN Node 2
+  comment: "DEV"
+  
+esphome:
+  name: mcu-${device}
+  comment: ${comment}
+
+esp32:
+  board: esp32dev
+  framework:
+    # type: arduino
+    type: esp-idf
+    # version: 5.1.2
+    # platform_version: 6.5.0
+
+external_components:
+  - source: github://mrk-its/esphome-canopen@dev
+    refresh: 1h
+
+packages:
+  common: !include common/common.yaml
+  
+canbus:
+  - platform: esp32_can
+    id: can_bus
+    rx_pin: 22
+    tx_pin: 23
+    can_id: 0
+    bit_rate: 125kbps
+
+canopen:
+  id: can_gate
+  canbus_id: can_bus
+  node_id: 2
+  entities:
+    - id: boot
+      index: 1
+      tpdo: 0
+    - id: blue_led
+      index: 2
+      tpdo: 0
+    - id: uptime_sensor
+      index: 3
+      tpdo: 0
+    - id: cover1
+      index: 4
+      tpdo: 1
+    # - id: cover2
+    #   index: 5
+    #   tpdo: 1
+
+sensor:
+  - platform: uptime
+    id: uptime_sensor
+    name: "${name} Uptime"
+    update_interval: 5sec
+    internal: true
+
+binary_sensor:
+  - platform: gpio
+    name: "${name} Boot"
+    id: boot
+    internal: true
+    pin:
+      number: 0
+      inverted: true
+
+switch:
+  - platform: gpio
+    name: "${name} Led"
+    id: blue_led
+    internal: true
+    pin: 2
+
+cover:
+  - platform: time_based
+    name: "${name} Cover"
+    id: cover1
+    internal: true
+    device_class: shutter
+    has_built_in_endstop: true
+    open_action:
+      - logger.log: open_action
+    open_duration: 10s
+    close_action:
+      - logger.log: close_action
+    close_duration: 10s
+    stop_action:
+      - logger.log: stop_action

mcu-cec-bedroom.yaml

@@ -10,8 +10,8 @@ esphome:
 esp32:
   board: m5stack-atom
   framework:
-    type: arduino
+    # type: arduino
-    # type: esp-idf
+    type: esp-idf
 
 external_components:
   # - source: github://pr#3017
@@ -61,13 +61,14 @@ binary_sensor:
       inverted: true
 
 light:
-  - platform: neopixelbus
+  - platform: esp32_rmt_led_strip
-    type: GRB
-    pin: 27
-    variant: WS2812
-    num_leds: 1
     name: "${name} LED"
-    id: neo
+    id: led
+    rgb_order: GRB
+    pin: 27
+    num_leds: 1
+    chipset: ws2812
+    restore_mode: ALWAYS_OFF
     effects:
       # Use default parameters:
       - random:

mcu-clock-1.yaml

@@ -14,8 +14,8 @@ esp32:
   variant: esp32c3
   framework:
     type: esp-idf
-    version: 5.1.2
+    # version: 5.2.1
-    platform_version: 6.5.0
+    # platform_version: 6.6.0
 
 packages:
   common: !include common/common.yaml

mcu-desk-lamp.yaml

@@ -11,9 +11,15 @@ esp32:
   board: m5stack-atom
   framework:
     type: esp-idf
-    version: 5.1.2
+    # version: 5.2.1
-    platform_version: 6.6.0
+    # platform_version: 6.6.0
-  
+
+# external_components:
+#   - source: github://pr#7958
+#     refresh: 0s
+#     components:
+#       - rotary_encoder
+
 packages:
   common: !include common/common.yaml
 
@@ -140,4 +146,4 @@ sensor:
             // apply new settings
             call.set_brightness(brightness);
             call.set_color_temperature(temp);
-            call.perform();
+            call.perform();

mcu-dev-temp.yaml

@@ -9,9 +9,9 @@ esphome:
 
 esp32:
   board: esp32doit-devkit-v1
-  # framework:
+  framework:
   #   type: arduino
-  #   # type: esp-idf
+    type: esp-idf
 
 external_components:
   - source: components
@@ -25,12 +25,12 @@ switch:
     id: sensor_power
     restore_mode: ALWAYS_ON
 
-dallas:
+one_wire:
-  - pin: GPIO25
+  - platform: gpio
-    update_interval: 10s
+    pin: GPIO25
 
 sensor:
-  - platform: dallas
+  - platform: dallas_temp
-    index: 0
     name: $name Dallas
-    id: temp
+    id: temp
+    update_interval: 10 s

mcu-dimmer.yaml

@@ -33,9 +33,8 @@ esp32:
     # type: arduino
     # version: 2.0.14
     type: esp-idf
-    # version: 5.1.2
+    # version: 5.2.1
-    version: 5.2.1
+    # platform_version: 6.6.0
-    platform_version: 6.6.0
 
 external_components:
   - source: github://pr#7072
@@ -57,7 +56,7 @@ light:
     rgb_order: GRB
     pin: 27
     num_leds: 1
-    rmt_channel: 0
+    # rmt_channel: 0
     chipset: ws2812
     restore_mode: ALWAYS_OFF
     effects:

mcu-echo-1.yaml

@@ -12,8 +12,8 @@ esp32:
   board: m5stack-atom
   framework:
     type: arduino
-    version: 2.0.14
+    # version: 2.0.14
-    platform_version: 6.5.0
+    # platform_version: 6.5.0
     # type: esp-idf
     # version: 5.1.2
     # platform_version: 6.5.0
@@ -32,7 +32,7 @@ external_components:
     refresh: 0s
 
 packages:
-  common: !include common/common.yaml
+  common: !include common/common_esp8266.yaml # this profile is without fancy features that are not supported by arduino
 
 api:
   services:
@@ -45,8 +45,8 @@ api:
             rtttl: !lambda 'return song;'
 
 # i2c:
-#   sda: 32
+  # sda: 26
-#   scl: 26
+  # scl: 32
 #   scan: true #false
 #   frequency: 100kHz
 
@@ -127,7 +127,7 @@ speaker:
     i2s_dout_pin:
       number: 22
       allow_other_uses: true
-    mode: mono
+    channel: mono
 
 rtttl:
   id: my_rtttl
@@ -140,10 +140,10 @@ microphone:
     adc_type: external
     pdm: true
 
-# voice_assistant:
+voice_assistant:
-#   microphone: echo_microphone
+  microphone: echo_microphone
-#   on_tts_end:
+  on_tts_end:
-#     - media_player.play_media:
+    - media_player.play_media:
-#         id: media_out
+        id: media_out
-#         media_url: !lambda |-
+        media_url: !lambda |-
-#           return x;
+          return x;

mcu-echo.yaml

@@ -26,7 +26,7 @@ external_components:
   #   refresh: 0s
 
 packages:
-  common: !include common/common.yaml
+  common: !include common/common_esp8266.yaml
 
 # api:
   # services:
@@ -39,8 +39,8 @@ packages:
   #           rtttl: !lambda 'return song;'
 
 i2c:
-  sda: 32
+  sda: 26
-  scl: 26
+  scl: 32
   scan: true #false
   frequency: 100kHz
 
@@ -133,25 +133,25 @@ media_player:
     dac_type: external
     i2s_dout_pin:
       number: 22
-      # allow_other_uses: true
+      allow_other_uses: true
     mode: mono
     on_play:
       - light.turn_on: led_light
     on_idle:
       - light.turn_off: led_light
 
-# speaker:
+speaker:
-#   - platform: i2s_audio
+  - platform: i2s_audio
-#     id: echo_speaker
+    id: echo_speaker
-#     dac_type: external
+    dac_type: external
-#     i2s_dout_pin:
+    i2s_dout_pin:
-#       number: 22
+      number: 22
-#       allow_other_uses: true
+      allow_other_uses: true
-#     mode: mono
+    channel: mono
 
-# rtttl:
+rtttl:
-#   id: my_rtttl
+  id: my_rtttl
-#   speaker: echo_speaker
+  speaker: echo_speaker
 
 # microphone:
 #   - platform: i2s_audio

mcu-fireplace-old.yaml

@@ -6,7 +6,8 @@ substitutions:
 esphome:
   name: mcu-${device}
   comment: ${comment}
-  platform: ESP8266
+
+esp8266:
   board: esp01_1m
 
 # wifi:
@@ -15,8 +16,9 @@ esphome:
 packages:
   common: !include common/common_esp8266.yaml
 
-dallas:
+one_wire:
-  - pin: 4
+  - platform: gpio
+    pin: 4
 
 binary_sensor:
   - platform: template
@@ -29,7 +31,7 @@ binary_sensor:
       }
 
 sensor:
-  - platform: dallas
+  - platform: dallas_temp
     address: 0x6203168B32A7FF28
     # index: 0
     name: "${name}"

mcu-fireplace.yaml

@@ -11,8 +11,8 @@ esp32:
   board: m5stack-atom
   framework:
     type: esp-idf
-    version: 5.1.2
+    # version: 5.1.2
-    platform_version: 6.6.0
+    # platform_version: 6.6.0
 
 external_components:
   - source: github://mknjc/esphome@ds248x

mcu-gate.yaml

@@ -11,8 +11,8 @@ esp32:
   board: m5stack-atom
   framework:
     type: esp-idf
-    version: 5.1.2
+    # version: 5.1.2
-    platform_version: 6.5.0
+    # platform_version: 6.5.0
 
 external_components:
   - source: components
@@ -97,6 +97,7 @@ switch:
 
 # Bluetooth related stuff
 esp32_ble_tracker:
+  id: ${name}_ble_tracker
   scan_parameters:
     duration: 1min
 

mcu-gateway.yaml

@@ -10,8 +10,8 @@ esphome:
 esp32:
   board: esp32doit-devkit-v1
   framework:
-    version: 5.1.2
+    # version: 5.1.2
-    platform_version: 6.6.0
+    # platform_version: 6.6.0
     type: esp-idf
 
 # external_components:
@@ -71,6 +71,12 @@ i2c:
   #   gateway: 10.17.240.1
   #   subnet: 255.255.255.0
 
+
+ethernet:
+  # use_address: 10.17.241.254
+  # use_address: 10.17.241.98
+  use_address: mcu-gateway.local
+
 uart:
   id: uart_modbus
   tx_pin: 4

mcu-heating.yaml

@@ -12,8 +12,8 @@ esp32:
   board: m5stack-atom
   framework:
     type: esp-idf
-    version: 5.1.2
+    # version: 5.1.2
-    platform_version: 6.6.0
+    # platform_version: 6.6.0
 
 external_components:
   - source: github://mknjc/esphome@ds248x
@@ -117,36 +117,6 @@ time:
     id: ha_time
     timezone: Europe/Bratislava
     on_time:
-      # - seconds: 0
-      #   minutes: 0
-      #   hours: 5
-      #   # days_of_week: MON-FRI
-      #   then:
-      #     - climate.control:
-      #         id: hot_water_climate
-      #         mode: "AUTO"
-      # - seconds: 0
-      #   minutes: 0
-      #   hours: 6
-      #   then:
-      #     - climate.control:
-      #         id: hot_water_climate
-      #         mode: "OFF"
-      # - seconds: 0
-      #   minutes: 0
-      #   hours: 16
-      #   # days_of_week: MON-FRI
-      #   then:
-      #     - climate.control:
-      #         id: hot_water_climate
-      #         mode: "AUTO"
-      # - seconds: 0
-      #   minutes: 0
-      #   hours: 0
-      #   then:
-      #     - climate.control:
-      #         id: hot_water_climate
-      #         mode: "OFF"
       - seconds: 0
         minutes: /1
         # hours: 5-23
@@ -154,72 +124,16 @@ time:
         then:
           lambda: |-
             if (id(hot_water_heater).state >= 67.0) {
-              id(relay_1).turn_off();
+              id(hot_water_demand).turn_off();
             }
-            // ## Solar
-            // move to temp sensor?
-            // //ESP_LOGD("main", "(hot_water_solar - current_hot_water_solar_delta) > set_hot_water_solar_temperature [(%.2f - %.2f) > %.2f] == TRUE", id(hot_water_solar).state, id(set_hot_water_solar_delta), id(set_hot_water_solar_temperature));
-            //if ((id(hot_water_solar).state <= id(set_hot_water_solar_temperature)) && ((id(temp_1).state + id(set_hot_water_solar_delta)) >= id(hot_water_solar).state)) {
-            //  ESP_LOGD("main", "Water in solar tank is colder AND temperature of solar collector is higher => ON");
-            //  id(relay_1).turn_on();
-            //}
-            //if ((id(hot_water_solar).state > id(set_hot_water_solar_temperature)) || ((id(temp_1).state - id(hot_water_solar).state) < (id(set_hot_water_solar_delta) / 2))) {
-            //  ESP_LOGD("main", "Water in solar tank is higher OR temperature of solar collector is lower => OFF");
-            //  id(relay_1).turn_off();
-            //}
 
-            // ## Hot Water
-            if (!true) {
-            if ((id(ha_time).now().hour >= 5) && (id(ha_time).now().hour <= 23)) {
-              if (id(hot_water_heater).state <= id(set_hot_water_heating_temperature_min)) {
-                ESP_LOGD("main", "Water in heated tank is cold, needs to reheat => ON");
-                id(relay_1).turn_on();
-                //id(relay_3).turn_on();
-                id(relay_4).turn_on();
-              } else {
-                if (id(hot_water_heater).state >= id(set_hot_water_heating_temperature_max)) {
-                  ESP_LOGD("main", "Water in heated tank is OK => OFF");
-                  id(relay_1).turn_off();
-                  //id(relay_3).turn_off();
-                  id(relay_4).turn_off();
-                }
-              }
-            } else {
-              ESP_LOGD("main", "Night Mode, Hot water heating => OFF");
-              id(relay_1).turn_off();
-            }
-            }
-            
             // ## Heating - TYPE 1: heat water to desired max temperature at specified times
             // ## Heating - TYPE 2: mantain temperature in min-max range in desired time range
-            //if ( (id(relay_2).state) && (id(heating_climate).mode == 0)) {
             if (id(heating_climate).mode == 0) {
-              id(relay_2).turn_off();
+              id(heating_demand).turn_off();
               ESP_LOGD("main", "Climate Heating is OFF => Turn Heating OFF!");
             } else {
-              ESP_LOGD("main", "Climate Heating state is other than OFFF => dont touch heating");
+              ESP_LOGD("main", "Climate Heating state is other than OFF => dont touch heating");
-            }
-            if (!true) {
-            //if (!id(heating_override).state) { // if not overriden from Thermosta
-              if (id(ha_time).now().hour >= 7 && id(ha_time).now().hour <= 23) { // is between 5:00-23:59
-                if ((id(current_heating_temperature_min).state <= id(set_heating_temperature_min)) && !id(heating_fireplace_status).state) { // temperature LOWER than set AND fireplace is NOT ON
-                  ESP_LOGD("main", "Is cold inside, heating => ON DISABLED");
-                  id(relay_2).turn_on();
-                } else {
-                  if (id(current_heating_temperature_min).state >= id(set_heating_temperature_max)) {
-                    ESP_LOGD("main", "Temperature is fine, heating => OFF");
-                    id(relay_2).turn_off();
-                  }
-                  if (id(heating_fireplace_status).state) {
-                    ESP_LOGD("main", "Fireplace is ON, heating => OFF");
-                    id(relay_2).turn_off();
-                  }
-                }
-              } else { // othervise night mode
-                ESP_LOGD("main", "Night Mode, heating => OFF");
-                id(relay_2).turn_off();
-              }
-            //}
             }
 
 climate:
@@ -235,9 +149,9 @@ climate:
     default_target_temperature_low: 48 °C
     default_target_temperature_high: 56 °C
     heat_action:
-      - switch.turn_on: relay_1
+      - switch.turn_on: hot_water_demand
     idle_action:
-      - switch.turn_off: relay_1
+      - switch.turn_off: hot_water_demand
     away_config:
       default_target_temperature_low: 30 °C
       default_target_temperature_high: 40 °C
@@ -252,22 +166,12 @@ climate:
     default_target_temperature_low: 19 °C
     default_target_temperature_high: 20 °C
     heat_action:
-      - switch.turn_on: relay_2
+      - switch.turn_on: heating_demand
     idle_action:
-      - switch.turn_off: relay_2
+      - switch.turn_off: heating_demand
     away_config:
       default_target_temperature_low: 17 °C
       default_target_temperature_high: 18 °C
-# interval:
-#   - interval: 5s
-#     then:
-#       - display.page.show_next: display_1
-#       # - display.page.show_next: display_2
-#       - component.update: display_1
-#       # - component.update: display_2
-
-# dallas:
-#   - pin: 32
 
 i2c:
   # - id: i2c0
@@ -298,113 +202,30 @@ uart:
     stop_bits: 2
     # debug:
 
-# light:
-#   - platform: neopixelbus
-#     type: GRB
-#     pin: 27
-#     variant: WS2812
-#     num_leds: 1
-#     name: "${name} Light"
-#     id: neo
-#     effects:
-#       # Use default parameters:
-#       - random:
-#       # Customize parameters
-#       - random:
-#           name: "My Slow Random Effect"
-#           transition_length: 30s
-#           update_interval: 30s
-#       - random:
-#           name: "My Fast Random Effect"
-#           transition_length: 4s
-#           update_interval: 5s
-#       - strobe:
-#       - strobe:
-#           name: Strobe Effect With Custom Values
-#           colors:
-#             - state: True
-#               brightness: 100%
-#               red: 100%
-#               green: 90%
-#               blue: 0%
-#               duration: 500ms
-#             - state: False
-#               duration: 250ms
-#             - state: True
-#               brightness: 100%
-#               red: 0%
-#               green: 100%
-#               blue: 0%
-#               duration: 500ms
-#       - flicker:
-#       - flicker:
-#           name: Flicker Effect With Custom Values
-#           alpha: 95%
-#           intensity: 1.5%
-#       - addressable_rainbow:
-#       - addressable_rainbow:
-#           name: Rainbow Effect With Custom Values
-#           speed: 10
-#           width: 50
-#       - addressable_scan:
-#       - addressable_scan:
-#           name: Scan Effect With Custom Values
-#           move_interval: 100ms
-
 pca9554:
   - id: pca9554_module
     address: 0x27
 
 switch:
-  # - platform: gpio
-  #   name: "${name} Relay 1" # Solar pump
-  #   id: relay_1
-  #   pin:
-  #     pcf8574: relay_module
-  #     number: 0
-  #     mode: OUTPUT
-  #     inverted: true
   - platform: gpio
-    name: "${name} Relay 2" # Hot Water Heating Demand (to Heater)
+    name: "Hot Water Demand" # Hot Water Heating Demand (to Heater)
-    id: relay_1
+    id: hot_water_demand
     pin: 22
     inverted: true
-    # pin:
-    #   mcp23xxx: relay_module
-    #   # pcf8574: relay_module
-    #   number: 0
-    #   mode: OUTPUT
-    #   inverted: true
-    # on_turn_on:
-    # - light.addressable_set:
-    #     id: neo
-    #     range_from: 1
-    #     range_to: 2
-    #     red: 0%
-    #     green: 100%
-    #     blue: 0%
-    # on_turn_off:
-    # - light.addressable_set:
-    #     id: neo
-    #     range_from: 1
-    #     range_to: 2
-    #     red: 100%
-    #     green: 0%
-    #     blue: 0%
   - platform: gpio
-    name: "${name} Relay 3" # Heating Demand (to Heater)
+    name: "Heating Demand" # Heating Demand (to Heater)
-    id: relay_2
+    id: heating_demand
     pin: 19
     inverted: true
   - platform: gpio
     name: "${name_1} Power Level II"
-    id: relay_3
+    id: heating_power_level_2
     pin:
       pca9554: pca9554_module
       number: 4
   - platform: gpio
     name: "${name_1} Power Level III"
-    id: relay_4
+    id: heating_power_level_3
     pin:
       pca9554: pca9554_module
       number: 5
@@ -432,14 +253,6 @@ sensor:
     address: 0x5A041750B2C8FF28 # Hot Water Tank - Bottom (Solar)
     name: "Hot Water - Solar"
     id: 'hot_water_solar'
-  # - platform: ds248x
-  #   address: 0xB2041750CF1AFF28 # Heating Water Feed (OUT from Heater, TO System)
-  #   name: "Heating OUT"
-  #   id: 'heating_out'
-  # - platform: ds248x
-  #   address: 0xDB041750EAE2FF28 # Heating Water Return (OUT from System, TO Heater)
-  #   name: "Heating IN"
-  #   id: 'heating_in'
   - platform: ds248x
     address: 0xF701143E397FAA28 # Heater Tank
     name: "Heater"
@@ -657,85 +470,6 @@ sensor:
     lambda: |-
       return id(heater_l1_energy).state + id(heater_l2_energy).state + id(heater_l3_energy).state ;
 
-# font:
-#   - file: 'slkscr.ttf'
-#     id: font_1
-#     size: 8
-#   - file: 'BebasNeue-Regular.ttf'
-#     id: font_2
-#     size: 48
-#   - file: 'arial.ttf'
-#     id: font_3
-#     size: 14
-#   - file: 'B612Mono-Regular.ttf'
-#     id: font_4
-#     size: 16
-
-# display:
-#   - platform: ssd1306_i2c
-#     model: "SSD1306 128x64"
-#     address: 0x3C # 0x78
-#     #address: 0x3D # 0x7A
-#     id: display_1
-#     pages:
-#       # - id: page_1
-#       #   lambda: |-
-#       #     it.print(0, 0, id(font_3), "TEMP 1");
-#       #     if (id(temp_1).has_state()) {
-#       #       it.printf(0, 16, id(font_2), TextAlign::TOP_LEFT, "%.1f°", id(temp_1).state);
-#       #     }
-#       # - id: page_2
-#       #   lambda: |-
-#       #     it.print(0, 0, id(font_3), "TEMP 2");
-#       #     if (id(temp_1).has_state()) {
-#       #       it.printf(0, 16, id(font_2), TextAlign::TOP_LEFT, "%.1f°", id(temp_2).state);
-#       #     }
-#       # - id: page_3
-#       #   lambda: |-
-#       #     it.print(0, 0, id(font_3), "TEMP 3");
-#       #     if (id(temp_1).has_state()) {
-#       #       it.printf(0, 16, id(font_2), TextAlign::TOP_LEFT, "%.1f°", id(temp_3).state);
-#       #     }
-#       # - id: page_4
-#       #   lambda: |-
-#       #     it.print(0, 0, id(font_3), "TEMP 4");
-#       #     if (id(temp_1).has_state()) {
-#       #       it.printf(0, 16, id(font_2), TextAlign::TOP_LEFT, "%.1f°", id(temp_4).state);
-#       #     }
-#       # - id: page_5
-#       #   lambda: |-
-#       #     it.printf(0,  0, id(font_1), TextAlign::TOP_LEFT, "RELAY 1: %s", id(relay_1).state ? "ON" : "OFF");
-#       #     it.printf(0,  8, id(font_1), TextAlign::TOP_LEFT, "RELAY 2: %s", id(relay_2).state ? "ON" : "OFF");
-#       #     it.printf(0, 16, id(font_1), TextAlign::TOP_LEFT, "RELAY 3: %s", id(relay_3).state ? "ON" : "OFF");
-#       #     it.printf(0, 24, id(font_1), TextAlign::TOP_LEFT, "RELAY 4: %s", id(relay_4).state ? "ON" : "OFF");
-#       - id: page_6
-#         lambda: |-
-#           it.print(0, 0, id(font_3), "Hot Water");
-#           it.printf(100,  0, id(font_3), TextAlign::TOP_LEFT, "%s", id(relay_2).state ? "ON" : "OFF");
-#           if (id(hot_water_heater).has_state()) {
-#             it.printf(0, 16, id(font_2), TextAlign::TOP_LEFT, "%.1f°", id(hot_water_heater).state);
-#           }
-
-#   - platform: ssd1306_i2c
-#     model: "SSD1306 128x64"
-#     #address: 0x3C # 0x78
-#     address: 0x3D # 0x7A
-#     id: display_2
-#     pages:
-#       - id: page_2_1
-#         lambda: |-
-#           it.print(0, 0, id(font_3), "Heating");
-#           it.printf(100,  0, id(font_3), TextAlign::TOP_LEFT, "%s", id(relay_3).state ? "ON" : "OFF");
-#           it.print(100, 32, id(font_1), TextAlign::BOTTOM_LEFT, "max");
-#           if (id(current_heating_temperature_max).has_state()) {
-#             it.printf(0, 32, id(font_4), TextAlign::BOTTOM_LEFT, "%.1f°", id(current_heating_temperature_max).state);
-#           }
-#           it.print(100, 48, id(font_1), TextAlign::BOTTOM_LEFT, "min");
-#           if (id(current_heating_temperature_min).has_state()) {
-#             it.printf(0, 48, id(font_4), TextAlign::BOTTOM_LEFT, "%.1f°", id(current_heating_temperature_min).state);
-#           }
-#           it.printf(0,  64, id(font_4), TextAlign::BOTTOM_LEFT, "%s", id(off_peak_status).state ? "OFF PEAK POWER" : "Disabled");
-
 binary_sensor:
   - platform: gpio
     name: "${name} Off Peak" # Off Peak (HDO)
@@ -764,15 +498,6 @@ binary_sensor:
     filters:
       - delayed_on: 300ms
       - delayed_off: 300ms
-  - platform: gpio
-    name: "${name} Input 3" # Heating Demand/Override (from Thermostat)
-    id: heating_override
-    pin:
-      pca9554: pca9554_module
-      number: 3
-    filters:
-      - delayed_on: 300ms
-      - delayed_off: 300ms
   - platform: template
     id: heating_fireplace_status
     lambda: |-
@@ -785,7 +510,7 @@ binary_sensor:
     id: heater_alarm
     name: "Heater Alarm"
     lambda: |-
-      if (id(off_peak_status).state && (id(relay_2).state || id(relay_3).state) && !id(heater_on).state) {
+      if (id(off_peak_status).state && (id(heating_demand).state || id(heating_power_level_2).state) && !id(heater_on).state) {
         return true;
       } else {
         return false;

mcu-irrigation-1.yaml

@@ -6,8 +6,6 @@ substitutions:
 esphome:
   name: mcu-${device}
   comment: ${comment}
-  platform: ESP8266
-  board: esp01_1m
   # on_boot:
   #   priority: -10
   #   then:
@@ -21,6 +19,9 @@ esphome:
   #     - delay: 2s
   #     - switch.turn_off: relay_5
 
+esp8266:
+  board: esp01_1m
+
 packages:
   common: !include common/common_esp8266.yaml
   

mcu-kitchen.yaml

@@ -29,8 +29,8 @@ esp32:
   board: m5stack-atom
   framework:
     type: esp-idf
-    version: 5.1.2
+    # version: 5.1.2
-    platform_version: 6.6.0
+    # platform_version: 6.6.0
 
 packages:
   common: !include common/common.yaml

mcu-lightening.yaml

@@ -13,8 +13,8 @@ esp32:
   # board: m5stamp-pico
   framework:
     type: esp-idf
-    version: 5.1.2
+    # version: 5.1.2
-    platform_version: 6.5.0
+    # platform_version: 6.5.0
 
 external_components:
   - source: components

mcu-lvgl.yaml

@@ -8,6 +8,7 @@ esphome:
   comment: ${comment}
   platformio_options:
     board_build.flash_mode: dio
+  includes: ota.h
 
 esp32:
   board: esp32-s3-devkitc-1
@@ -15,8 +16,8 @@ esp32:
   flash_size: 16MB
   framework:
     type: esp-idf
-    version: 5.1.2
+    # version: 5.1.2
-    platform_version: 6.5.0
+    # platform_version: 6.5.0
     # Required to achieve sufficient PSRAM bandwidth
     sdkconfig_options:
       CONFIG_ESP32S3_DEFAULT_CPU_FREQ_240: y
@@ -31,13 +32,6 @@ psram:
 packages:
   common: !include common/common.yaml
 
-external_components:
-  - source:
-      type: git
-      url: https://github.com/clydebarrow/esphome
-      ref: fd15094c0860df23d532881df36cfd16c7da1091 #previous commit - wont be needed in the future
-    components: [ lvgl ]
-
 # PINOUTS: ESP32 Cheap Yellow Display, 4.3", IPS, Capacitive 
 ## Display
 # R0        GND
@@ -177,8 +171,8 @@ number:
     step: 1
     optimistic: True
 
-debug:
+# debug:
-  update_interval: 5s
+#   update_interval: 5s
 
 sensor:
   - platform: uptime
@@ -194,15 +188,15 @@ sensor:
             id: counting_number
             cycle: True
         - script.execute: update_display
-  - platform: debug
+  # - platform: debug
-    free:
+  #   free:
-      name: "${name} Heap Free"
+  #     name: "${name} Heap Free"
-    block:
+  #   block:
-      name: "${name} Heap Max Block"
+  #     name: "${name} Heap Max Block"
-    loop_time:
+  #   loop_time:
-      name: "${name} Loop Time"
+  #     name: "${name} Loop Time"
-    psram:
+  #   psram:
-      name: "${name} Free PSRAM"
+  #     name: "${name} Free PSRAM"
   - platform: uptime
     # name: Uptime Sensor
     internal: True
@@ -231,9 +225,9 @@ sensor:
 script:
   - id: update_display
     then:
-      - lvgl.indicator.line.update:
+      # - lvgl.indicator.line.update:
-          id: power_meter_input
+      #     id: power_meter_input
-          value: !lambda return id(counting_number).state;
+      #     value: !lambda return id(counting_number).state;
       - lvgl.label.update:
           id: battery_kw
           text: !lambda |-
@@ -257,15 +251,15 @@ script:
             static char buf[8];
             snprintf(buf, sizeof(buf), "%.1fkW", id(counting_number).state);
             return buf;
-      - lvgl.img.update:
+      # - lvgl.img.update:
-          id: img_solar_power
+      #     id: img_solar_power
-          src: solar_power_icon
+      #     src: solar_power_icon
-          img_recolor: 0xFFF000 #mixes this color with the base image
+      #     img_recolor: 0xFFF000 #mixes this color with the base image
-          #img_recolor_opa: 100% #opacity defaults to 0% = must set this for recolor to take effect
+      #     #img_recolor_opa: 100% #opacity defaults to 0% = must set this for recolor to take effect
-          #bg_color: 0xFFFFFF          
+      #     #bg_color: 0xFFFFFF          
-      - lvgl.indicator.line.update:
+      # # - lvgl.indicator.line.update:
-          id: power_meter_input2
+      # #     id: power_meter_input2
-          value: !lambda return id(counting_number).state;
+      # #     value: !lambda return id(counting_number).state;
       - lvgl.label.update:
           id: battery_kw2
           text: !lambda |-
@@ -289,12 +283,12 @@ script:
             static char buf[8];
             snprintf(buf, sizeof(buf), "%.1fkW", id(counting_number).state);
             return buf;
-      - lvgl.img.update:
+      # - lvgl.img.update:
-          id: img_solar_power2
+      #     id: img_solar_power2
-          src: solar_power_icon
+      #     src: solar_power_icon
-          img_recolor: 0xFFF000 #mixes this color with the base image
+      #     img_recolor: 0xFFF000 #mixes this color with the base image
-          #img_recolor_opa: 100% #opacity defaults to 0% = must set this for recolor to take effect
+      #     #img_recolor_opa: 100% #opacity defaults to 0% = must set this for recolor to take effect
-          #bg_color: 0xFFFFFF   
+      #     #bg_color: 0xFFFFFF   
 
 image:
   - file: mdi:sun-wireless-outline

mcu-mains-power.yaml

@@ -12,8 +12,8 @@ esp32:
   board: m5stack-atom
   framework:
     type: esp-idf
-    version: 5.1.2
+    # version: 5.1.2
-    platform_version: 6.6.0
+    # platform_version: 6.6.0
   
 packages:
   common: !include common/common.yaml

mcu-nspanel-bedroom.yaml

@@ -10,6 +10,11 @@ substitutions:
 esphome:
   name: mcu-${device}
   comment: ${comment}
+  on_boot:
+    then:
+      - switch.turn_off: screen_power
+      - delay: 1s
+      - switch.turn_on: screen_power
 
 esp32:
   board: nodemcu-32s
@@ -22,6 +27,9 @@ external_components:
       url: https://github.com/sairon/esphome-nspanel-lovelace-ui
       ref: dev
     components: [nspanel_lovelace]
+  - source: github://pr#7942
+    components: adc
+    refresh: 0s
   - source: components
   
 packages:

mcu-nspanel-dev.yaml

@@ -10,7 +10,12 @@ substitutions:
 esphome:
   name: mcu-${device}
   comment: ${comment}
-  # on_boot:
+  on_boot:
+    then:
+      - switch.turn_off: screen_power
+      - delay: 1s
+      - switch.turn_on: screen_power
+
   #   priority: -100
   #   then:
   #     - wait_until:
@@ -35,6 +40,9 @@ external_components:
       ref: dev
     refresh: 0s
     components: [nspanel_lovelace]
+  - source: github://pr#7942
+    components: adc
+    refresh: 0s
   - source: components
   
 packages:

mcu-nspanel-fireplace.yaml

@@ -10,6 +10,11 @@ substitutions:
 esphome:
   name: mcu-${device}
   comment: ${comment}
+  on_boot:
+    then:
+      - switch.turn_off: screen_power
+      - delay: 1s
+      - switch.turn_on: screen_power
 
 esp32:
   board: nodemcu-32s
@@ -22,6 +27,9 @@ external_components:
       url: https://github.com/sairon/esphome-nspanel-lovelace-ui
       ref: dev
     components: [nspanel_lovelace]
+  - source: github://pr#7942
+    components: adc
+    refresh: 0s
   - source: components
   
 packages:

mcu-nspanel-office-j.yaml

@@ -10,6 +10,11 @@ substitutions:
 esphome:
   name: mcu-${device}
   comment: ${comment}
+  on_boot:
+    then:
+      - switch.turn_off: screen_power
+      - delay: 1s
+      - switch.turn_on: screen_power
 
 esp32:
   board: nodemcu-32s
@@ -22,6 +27,9 @@ external_components:
       url: https://github.com/sairon/esphome-nspanel-lovelace-ui
       ref: dev
     components: [nspanel_lovelace]
+  - source: github://pr#7942
+    components: adc
+    refresh: 0s
   - source: components
   
 packages:

mcu-nspanel-office-r.yaml

@@ -10,6 +10,11 @@ substitutions:
 esphome:
   name: mcu-${device}
   comment: ${comment}
+  on_boot:
+    then:
+      - switch.turn_off: screen_power
+      - delay: 1s
+      - switch.turn_on: screen_power
 
 esp32:
   board: nodemcu-32s
@@ -22,6 +27,9 @@ external_components:
       url: https://github.com/sairon/esphome-nspanel-lovelace-ui
       ref: dev
     components: [nspanel_lovelace]
+  - source: github://pr#7942
+    components: adc
+    refresh: 0s
   - source: components
   
 packages:
@@ -248,7 +256,7 @@ light:
     rgb_order: GRB
     pin: 23
     num_leds: 3
-    rmt_channel: 0
+    # rmt_channel: 0
     chipset: SK6812
     effects:
       - pulse:

mcu-nspanel-patio.yaml

@@ -10,6 +10,11 @@ substitutions:
 esphome:
   name: mcu-${device}
   comment: ${comment}
+  on_boot:
+    then:
+      - switch.turn_off: screen_power
+      - delay: 1s
+      - switch.turn_on: screen_power
 
 esp32:
   board: nodemcu-32s
@@ -22,6 +27,9 @@ external_components:
       url: https://github.com/sairon/esphome-nspanel-lovelace-ui
       ref: dev
     components: [nspanel_lovelace]
+  - source: github://pr#7942
+    components: adc
+    refresh: 0s
   - source: components
   
 packages:

mcu-office-r.yaml

@@ -14,11 +14,9 @@ esp32:
   board: esp32-c3-devkitm-1
   variant: esp32c3
   framework:
-    # type: arduino
-    # version: 2.0.14
     type: esp-idf
-    version: 5.1.2
+    # version: 5.1.2
-    platform_version: 6.5.0
+    # platform_version: 6.5.0
 
 packages:
   common: !include common/common.yaml

mcu-patio.yaml

@@ -29,8 +29,8 @@ esp32:
   board: m5stack-atom
   framework:
     type: esp-idf
-    version: 5.1.2
+    # version: 5.1.2
-    platform_version: 6.5.0
+    # platform_version: 6.5.0
 
 packages:
   common: !include common/common.yaml

mcu-pow-1.yaml

@@ -0,0 +1,204 @@
+substitutions:
+  device: pow-1
+  name: POW 1
+  comment: "DEV"
+  update_interval: 10s
+  
+esphome:
+  name: mcu-${device}
+  comment: ${comment}
+  on_boot: # Set the initial state of the template switch to the actual relay state. This will NOT change the state.
+    priority: 250.0 # Wait until WiFi is connected to allow the sensor some time to settle
+    then:
+      - if:
+          condition:
+            lambda: 'return id(v_sensor).state > 10;'
+          then:
+            - switch.turn_on: relay_1
+          else:
+            - switch.turn_off: relay_1
+
+esp32:
+  board: nodemcu-32s
+  framework:
+    type: esp-idf
+
+interval:
+  - interval: 30s
+    then:
+      if:
+        condition:
+          wifi.connected:
+        then:
+          - light.turn_on: wifi_status_led
+        else:
+          - light.turn_off: wifi_status_led
+
+packages:
+  common: !include common/common.yaml
+
+uart:
+  rx_pin: 16
+  baud_rate: 4800
+  parity: EVEN
+
+binary_sensor:
+  - platform: gpio
+    pin: 0
+    id: reset
+    internal: true
+    filters:
+      - invert:
+      - delayed_off: 10ms
+    on_click:
+      - max_length: 350ms # short press to toggle the relay
+        then:
+          switch.toggle: relay_1
+      - min_length: 360ms # long press to cycle display info
+        max_length: 3s
+        then:
+          - if:
+              condition:
+                binary_sensor.is_on: page
+              then:
+                binary_sensor.template.publish:
+                  id: page
+                  state: OFF
+              else:
+                binary_sensor.template.publish:
+                  id: page
+                  state: ON
+  - platform: template # this is a fake sensor to tell the screen which info to show on display
+    id: page
+    publish_initial_state: true
+    internal: true
+  - platform: template
+    name: "${name} Load"
+    id: load_on
+    lambda: |-
+      if (isnan(id(w_sensor).state)) {
+        return {};
+      } else if (id(w_sensor).state > 4) {
+        // Running
+        return true;
+      } else {
+        // Not running
+        return false;
+      }
+
+display:
+  platform: tm1621
+  id: tm1621_display
+  cs_pin: 25
+  data_pin: 14
+  read_pin: 26
+  write_pin: 27
+  lambda: |-
+    if (id(page).state) {
+      it.display_voltage(true);
+      it.display_kwh(false);
+      it.printf(0, "%.1f", id(v_sensor).state);
+      it.printf(1, "%.1f", id(a_sensor).state);
+    } else {  
+      it.display_voltage(false);
+      it.display_kwh(true);
+      it.printf(0, "%.1f", id(wh_sensor).state);
+      it.printf(1, "%.1f", id(w_sensor).state);
+    }
+
+light:
+  - platform: monochromatic
+    id: switch_led
+    output: led
+    internal: True
+  - platform: status_led
+    id: wifi_status_led
+    internal: True
+    pin:
+      number: 5
+      inverted: True
+
+output:
+  - platform: ledc
+    id: led
+    pin:
+      number: 18
+      inverted: True
+
+sensor:
+  - platform: cse7766
+    current:
+      name: "${name} Current"
+      id: a_sensor
+      filters:
+        - throttle_average: ${update_interval}
+    voltage:
+      name: "${name} Voltage"
+      id: v_sensor
+      filters:
+        - throttle_average: ${update_interval}
+    power:
+      name: "${name} Power"
+      id: w_sensor
+      filters:
+        - throttle_average: ${update_interval}
+      on_value_range:
+        - above: 4.0
+          then:
+            - light.turn_on: switch_led
+        - below: 3.0
+          then:
+            - light.turn_off: switch_led
+    energy:
+      name: "${name} Energy"
+      id: wh_sensor
+      filters:
+        - throttle_average: ${update_interval}
+
+  - platform: total_daily_energy
+    name: "${name} Total Daily Energy"
+    power_id: w_sensor
+    filters:
+      - multiply: 0.001
+    unit_of_measurement: kWh
+
+  - platform: template
+    name: "${name} Power Factor"
+    device_class: power_factor
+    id: power_factor
+    lambda: return id(w_sensor).state / id(v_sensor).state / id(a_sensor).state;
+
+switch:
+  - platform: template
+    name: "${name} Relay"
+    optimistic: true
+    id: relay_1
+    turn_off_action:
+      - switch.turn_on: relay_off
+    turn_on_action:
+      - switch.turn_on: relay_on
+  - platform: gpio
+    restore_mode: ALWAYS_OFF
+    internal: true
+    id: relay_off
+    pin: 4
+    on_turn_on:
+      - delay: 500ms
+      - switch.turn_off: relay_off # bi-stable relay so no need to keep on
+      - light.turn_off: switch_led
+    interlock: [relay_on]
+  - platform: gpio
+    restore_mode: ALWAYS_OFF
+    internal: true
+    id: relay_on
+    pin: 2
+    on_turn_on:
+      - delay: 500ms
+      - switch.turn_off: relay_on  # bi-stable relay so no need to keep on
+      - light.turn_on: switch_led
+    interlock: [relay_off]
+
+time:
+  - platform: homeassistant
+    id: ha_time
+    timezone: Europe/Bratislava

mcu-pow-2.yaml

@@ -0,0 +1,204 @@
+substitutions:
+  device: pow-2
+  name: POW 2
+  comment: "DEV"
+  update_interval: 10s
+  
+esphome:
+  name: mcu-${device}
+  comment: ${comment}
+  on_boot: # Set the initial state of the template switch to the actual relay state. This will NOT change the state.
+    priority: 250.0 # Wait until WiFi is connected to allow the sensor some time to settle
+    then:
+      - if:
+          condition:
+            lambda: 'return id(v_sensor).state > 10;'
+          then:
+            - switch.turn_on: relay_1
+          else:
+            - switch.turn_off: relay_1
+
+esp32:
+  board: nodemcu-32s
+  framework:
+    type: esp-idf
+
+interval:
+  - interval: 30s
+    then:
+      if:
+        condition:
+          wifi.connected:
+        then:
+          - light.turn_on: wifi_status_led
+        else:
+          - light.turn_off: wifi_status_led
+
+packages:
+  common: !include common/common.yaml
+
+uart:
+  rx_pin: 16
+  baud_rate: 4800
+  parity: EVEN
+
+binary_sensor:
+  - platform: gpio
+    pin: 0
+    id: reset
+    internal: true
+    filters:
+      - invert:
+      - delayed_off: 10ms
+    on_click:
+      - max_length: 350ms # short press to toggle the relay
+        then:
+          switch.toggle: relay_1
+      - min_length: 360ms # long press to cycle display info
+        max_length: 3s
+        then:
+          - if:
+              condition:
+                binary_sensor.is_on: page
+              then:
+                binary_sensor.template.publish:
+                  id: page
+                  state: OFF
+              else:
+                binary_sensor.template.publish:
+                  id: page
+                  state: ON
+  - platform: template # this is a fake sensor to tell the screen which info to show on display
+    id: page
+    publish_initial_state: true
+    internal: true
+  - platform: template
+    name: "${name} Load"
+    id: load_on
+    lambda: |-
+      if (isnan(id(w_sensor).state)) {
+        return {};
+      } else if (id(w_sensor).state > 4) {
+        // Running
+        return true;
+      } else {
+        // Not running
+        return false;
+      }
+
+display:
+  platform: tm1621
+  id: tm1621_display
+  cs_pin: 25
+  data_pin: 14
+  read_pin: 26
+  write_pin: 27
+  lambda: |-
+    if (id(page).state) {
+      it.display_voltage(true);
+      it.display_kwh(false);
+      it.printf(0, "%.1f", id(v_sensor).state);
+      it.printf(1, "%.1f", id(a_sensor).state);
+    } else {  
+      it.display_voltage(false);
+      it.display_kwh(true);
+      it.printf(0, "%.1f", id(wh_sensor).state);
+      it.printf(1, "%.1f", id(w_sensor).state);
+    }
+
+light:
+  - platform: monochromatic
+    id: switch_led
+    output: led
+    internal: True
+  - platform: status_led
+    id: wifi_status_led
+    internal: True
+    pin:
+      number: 5
+      inverted: True
+
+output:
+  - platform: ledc
+    id: led
+    pin:
+      number: 18
+      inverted: True
+
+sensor:
+  - platform: cse7766
+    current:
+      name: "${name} Current"
+      id: a_sensor
+      filters:
+        - throttle_average: ${update_interval}
+    voltage:
+      name: "${name} Voltage"
+      id: v_sensor
+      filters:
+        - throttle_average: ${update_interval}
+    power:
+      name: "${name} Power"
+      id: w_sensor
+      filters:
+        - throttle_average: ${update_interval}
+      on_value_range:
+        - above: 4.0
+          then:
+            - light.turn_on: switch_led
+        - below: 3.0
+          then:
+            - light.turn_off: switch_led
+    energy:
+      name: "${name} Energy"
+      id: wh_sensor
+      filters:
+        - throttle_average: ${update_interval}
+
+  - platform: total_daily_energy
+    name: "${name} Total Daily Energy"
+    power_id: w_sensor
+    filters:
+      - multiply: 0.001
+    unit_of_measurement: kWh
+
+  - platform: template
+    name: "${name} Power Factor"
+    device_class: power_factor
+    id: power_factor
+    lambda: return id(w_sensor).state / id(v_sensor).state / id(a_sensor).state;
+
+switch:
+  - platform: template
+    name: "${name} Relay"
+    optimistic: true
+    id: relay_1
+    turn_off_action:
+      - switch.turn_on: relay_off
+    turn_on_action:
+      - switch.turn_on: relay_on
+  - platform: gpio
+    restore_mode: ALWAYS_OFF
+    internal: true
+    id: relay_off
+    pin: 4
+    on_turn_on:
+      - delay: 500ms
+      - switch.turn_off: relay_off # bi-stable relay so no need to keep on
+      - light.turn_off: switch_led
+    interlock: [relay_on]
+  - platform: gpio
+    restore_mode: ALWAYS_OFF
+    internal: true
+    id: relay_on
+    pin: 2
+    on_turn_on:
+      - delay: 500ms
+      - switch.turn_off: relay_on  # bi-stable relay so no need to keep on
+      - light.turn_on: switch_led
+    interlock: [relay_off]
+
+time:
+  - platform: homeassistant
+    id: ha_time
+    timezone: Europe/Bratislava

mcu-rf433.yaml

@@ -6,7 +6,8 @@ substitutions:
 esphome:
   name: mcu-${device}
   comment: ${comment}
-  platform: ESP8266
+
+esp8266:
   board: esp01_1m
 
 packages:

mcu-shed.yaml

@@ -11,8 +11,8 @@ esp32:
   board: m5stack-atom
   framework:
     type: esp-idf
-    version: 5.1.2
+    # version: 5.1.2
-    platform_version: 6.6.0
+    # platform_version: 6.6.0
 
 packages:
   common: !include common/common.yaml

mcu-socket-01.yaml

@@ -9,7 +9,8 @@ substitutions:
 esphome:
   name: mcu-${device}
   comment: ${comment}
-  platform: ESP8266
+
+esp8266:
   board: esp01_1m
 
 packages:

mcu-socket-02.yaml

@@ -9,7 +9,8 @@ substitutions:
 esphome:
   name: mcu-${device}
   comment: ${comment}
-  platform: ESP8266
+
+esp8266:
   board: esp01_1m
 
 packages:

mcu-socket-03.yaml

@@ -16,7 +16,8 @@ substitutions:
 esphome:
   name: mcu-${device}
   comment: ${comment}
-  platform: ESP8266
+
+esp8266:
   board: esp01_1m
 
 packages:

mcu-staircase-light.yaml

@@ -42,7 +42,7 @@ binary_sensor:
     #     - light.turn_off: light_blue
   - platform: homeassistant
     id: motion
-    entity_id: binary_sensor.zigbee_staircase_pir_motion
+    entity_id: binary_sensor.zigbee_staircase_pir_occupancy
     on_state:
       if:
         condition:

mcu-tv-light.yaml

@@ -6,18 +6,12 @@ substitutions:
 esphome:
   name: mcu-${device}
   comment: ${comment}
-  platform: ESP8266
+
+esp8266:
   board: esp8285
 
 packages:
   common: !include common/common_esp8266.yaml
-  
-# Module type 	18 Generic 	Module type
-# D2 GPIO4 	51 IRRecv 	IR Remote (optional, view console for debugging!)
-# D1 GPIO5 	38 PWM2 	BLUE
-# D6 GPIO12 	37 PWM1 	RED
-# D7 GPIO13 	39 PWM3 	GREEN
-# D8 GPIO15 	40 PWM4 	WHITE
 
 ## H801 LED module
 # Function 	Pin 	  Channel
@@ -33,15 +27,6 @@ light:
   - platform: status_led
     id: status_led_id
     pin: 5
-  # - platform: rgbww
-  #   name: "${name}"
-  #   red: pwm_red
-  #   green: pwm_green
-  #   blue: pwm_blue
-  #   cold_white: pwm_cold_white
-  #   warm_white: pwm_warm_white
-  #   cold_white_color_temperature: 6536 K
-  #   warm_white_color_temperature: 2000 K
   - platform: monochromatic
     name: "${name}"
     output: pwm_cold_white

mcu-vehicle-toyota-auris-ts.yaml

@@ -34,8 +34,8 @@ esp32:
   board: m5stack-atom
   framework:
     type: esp-idf
-    version: 5.1.2
+    # version: 5.1.2
-    platform_version: 6.5.0
+    # platform_version: 6.5.0
 
 external_components:
   - source: components
@@ -43,12 +43,12 @@ external_components:
 packages:
   wifi: !include common/wifi.yaml
   logger: !include common/logger.yaml
-  api: !include common/api.yaml
+  # api: !include common/api.yaml
   ota: !include common/ota.yaml
 #   common: !include common/common.yaml
 
-api:
+# api:
-  reboot_timeout: 0s
+#   reboot_timeout: 0s
 
 wifi:
   reboot_timeout: 0s

mcu-vehicle-toyota-yaris-cross.yaml

@@ -46,6 +46,7 @@ external_components:
 
 packages:
   common: !include common/logger.yaml
+  wifi: !include common/wifi.yaml
   # common: !include common/common.yaml
   
 # debug:

mcu-waterproof-socket.yaml

@@ -6,7 +6,8 @@ substitutions:
 esphome:
   name: mcu-${device}
   comment: ${comment}
-  platform: ESP8266
+
+esp8266:
   board: esp01_1m
 
 packages:

mcu-well.yaml

@@ -24,8 +24,8 @@ esp32:
   board: m5stack-atom
   framework:
     type: esp-idf
-    version: 5.1.2
+    # version: 5.1.2
-    platform_version: 6.6.0
+    # platform_version: 6.6.0
 
 packages:
   common: !include common/common.yaml