mirror of
https://github.com/randybb/esphome-configs.git
synced 2026-10-14 08:35:12 +02:00
randy
7517c301ac
common/status_led_atom.yaml puts common/status_led.yaml on the ATOM Lite's own RGB LED (G27, 64 RMT symbols to leave room for IR/RF). echo-1 uses its existing LED light.
147 lines
3.2 KiB
YAML
147 lines
3.2 KiB
YAML
---
|
|
# Hardware: M5Stack ATOM Lite + ATOM Hub Switch
|
|
# Pinout:
|
|
# GPIO1 UART0 TX
|
|
# GPIO3 UART0 RX
|
|
# GPIO12 IR
|
|
# GPIO19 Relay2
|
|
# GPIO21 I2C1 SCL -> i2c (i2c scl)
|
|
# GPIO22 Relay1
|
|
# GPIO23 RS485 Tx
|
|
# GPIO25 I2C1 SDA - red -> i2c (i2c sda)
|
|
# GPIO26 I2C0 SDA - white
|
|
# GPIO27 NEO 1x -> atom_led (status LED, common/status_led_atom.yaml)
|
|
# GPIO32 I2C0 SCL
|
|
# GPIO33 RS485 Rx
|
|
# GPIO39 BUTTON -> Status Button (binary_sensor gpio)
|
|
# I2C:
|
|
# 0x18 one_wire_bus (one_wire ds2482)
|
|
# 0x27 pca9554_module (pca9554)
|
|
substitutions:
|
|
device: fireplace
|
|
name: Heating Fireplace
|
|
area: Living Room & Kitchen
|
|
comment: Fireplace monitoring for heating
|
|
|
|
esphome:
|
|
name: mcu-${device}
|
|
friendly_name: ${name}
|
|
area: ${area}
|
|
comment: ${comment}
|
|
|
|
esp32:
|
|
variant: esp32
|
|
toolchain: esp-idf
|
|
framework:
|
|
type: esp-idf
|
|
|
|
external_components:
|
|
# - source: github://pr#12717
|
|
# components: [ds248x]
|
|
# refresh: 1h
|
|
- source: github://pr#13534
|
|
components: [ds2482, ds2484, ds248x_base]
|
|
refresh: 1h
|
|
|
|
packages:
|
|
common: !include common/common.yaml
|
|
ipv6_only: !include common/ipv6_only.yaml
|
|
status_led: !include common/status_led_atom.yaml
|
|
|
|
|
|
i2c:
|
|
# - id: i2c0
|
|
# sda: 26
|
|
# scl: 32
|
|
# scan: true #false
|
|
# - id: i2c1
|
|
sda: 25
|
|
scl: 21
|
|
scan: true #false
|
|
|
|
# ds248x:
|
|
# # i2c_id: i2c_main
|
|
# address: 0x18 # should be the default
|
|
# # sleep_pin: 32 # remove if not needed, if set the ds248x sleeps when no transaction is in progress
|
|
# active_pullup: true # adds a active pullup which should improve signal integrity
|
|
# strong_pullup: false # enables a strong pullup used to provide the needed current for temperature reading without vcc connected
|
|
# bus_sleep: true # power down the bus when no transaction is in progres
|
|
|
|
# one_wire:
|
|
# id: one_wire_bus
|
|
# platform: ds2484
|
|
# active_pullup: true
|
|
|
|
# ds248x:
|
|
# id: ds2484_module
|
|
# address: 0x18
|
|
|
|
# one_wire:
|
|
# - platform: ds248x
|
|
# ds248x_id: ds2484_module
|
|
# id: one_wire_bus
|
|
|
|
one_wire:
|
|
id: one_wire_bus
|
|
platform: ds2482
|
|
active_pullup: true
|
|
|
|
pca9554:
|
|
- id: pca9554_module
|
|
address: 0x27
|
|
|
|
# modbus:
|
|
# uart_id: uart1
|
|
|
|
# uart:
|
|
# - id: uart1
|
|
# rx_pin: 33
|
|
# tx_pin: 32
|
|
# baud_rate: 9600
|
|
# stop_bits: 2
|
|
|
|
binary_sensor:
|
|
- platform: gpio
|
|
name: Status Button
|
|
filters:
|
|
- invert:
|
|
pin: 39
|
|
- platform: template
|
|
name: Fire
|
|
lambda: |-
|
|
if (id(heating_fireplace_temperature).state > 37.5) {
|
|
return true;
|
|
} else {
|
|
return false;
|
|
}
|
|
- platform: gpio
|
|
name: Pump
|
|
id: off_peak_status
|
|
pin:
|
|
pca9554: pca9554_module
|
|
number: 0
|
|
filters:
|
|
- delayed_on: 300ms
|
|
- delayed_off: 300ms
|
|
|
|
sensor:
|
|
# - platform: ds248x
|
|
- platform: dallas_temp
|
|
address: 0x6203168B32A7FF28
|
|
# index: 0
|
|
name: Temperature
|
|
id: 'heating_fireplace_temperature'
|
|
# - platform: dht
|
|
# pin: 14
|
|
# temperature:
|
|
# name: "Kitchen Temperature"
|
|
# id: 'kitchen_temperature'
|
|
# humidity:
|
|
# name: "Kitchen Humidity"
|
|
# id: 'kitchen_humidity'
|
|
# update_interval: 60s
|
|
# model: si7021
|
|
|
|
bluetooth_proxy:
|
|
active: true
|