Add archive to git ignore

Add friendly_name to make HA folks happy

.gitignore

@@ -3,4 +3,5 @@
 # You can modify this file to suit your needs.
 /.esphome/
 /secrets.yaml
+/archive/
 /trash/

common/binary_sensor/status.yaml

@@ -1,3 +1,3 @@
 ---
 platform: status
-name: "${name} Status"
+name: Status

common/button/factory_reset.yaml

@@ -1,3 +1,3 @@
 ---
 platform: factory_reset
-name: ${name} Factory Defaults
+name: Factory Defaults

common/button/restart.yaml

@@ -1,3 +1,3 @@
 ---
 platform: restart
-name: ${name} Restart
+name: Restart

common/button/safe_mode.yaml

@@ -1,3 +1,3 @@
 ---
 platform: safe_mode
-name: ${name} Restart (Safe Mode)
+name: Restart (Safe Mode)

common/button/shutdown.yaml

@@ -1,3 +1,3 @@
 ---
 platform: shutdown
-name: ${name} Shutdown
+name: Shutdown

common/ethernet.yaml

@@ -3,6 +3,7 @@ ethernet:
   type: LAN8720
   mdc_pin: 23
   mdio_pin: 18
-  clk_mode: GPIO17_OUT
+  clk_pin: 17
+  clk_mode: CLK_OUT
   phy_addr: 0
   power_pin: 12

common/sensor/debug.yaml

@@ -1,10 +1,10 @@
 ---
 platform: debug
 free:
-  name: "${name} Heap Free"
+  name: Heap Free
 fragmentation:
-  name: "${name} Heap Fragmentation"
+  name: Heap Fragmentation
 block:
-  name: "${name} Heap Max Block"
+  name: Heap Max Block
 loop_time:
-  name: "${name} Loop Time"
+  name: Loop Time

common/sensor/free_heap.yaml

@@ -1,6 +1,6 @@
 ---
 platform: template
-name: ${name} Free heap
+name: Free heap
 lambda: return heap_caps_get_free_size(MALLOC_CAP_INTERNAL);
 icon: "mdi:memory"
 entity_category: diagnostic

common/sensor/uptime.yaml

@@ -1,6 +1,6 @@
 ---
 platform: uptime
-name: ${name} Uptime
+name: Uptime
 unit_of_measurement: "days"
 accuracy_decimals: 2
 update_interval: 60s

common/sensor/wifi_signal.yaml

@@ -1,4 +1,4 @@
 ---
 platform: wifi_signal
-name: "${name} WiFi Signal"
+name: WiFi Signal
 update_interval: 60s

common/switch/restart.yaml

@@ -1,3 +1,3 @@
 ---
 platform: restart
-name: ${name} Restart
+name: Restart

common/switch/safe_mode.yaml

@@ -1,3 +1,3 @@
 ---
 platform: safe_mode
-name: ${name} Restart (Safe Mode)
+name: Restart (Safe Mode)

common/switch/shutdown.yaml

@@ -1,3 +1,3 @@
 ---
 platform: shutdown
-name: ${name} Shutdown
+name: Shutdown

common/text_sensor/debug.yaml

@@ -1,6 +1,6 @@
 ---
 platform: debug
 device:
-  name: "${name} Device Info"
+  name: Device Info
 reset_reason:
-  name: "${name} Reset Reason"
+  name: Reset Reason

common/text_sensor/ethernet_info.yaml

@@ -1,8 +1,8 @@
 ---
 platform: ethernet_info
 ip_address:
-  name: ${name} IP Address
+  name: IP Address
   address_1:
-    name: ${name} IP Address 1
+    name: IP Address 1
   address_2:
-    name: ${name} IP Address 2
+    name: IP Address 2

common/text_sensor/git_ref.yaml

@@ -1,6 +1,6 @@
 ---
 platform: git_ref
-name: "${name} Git Ref"
+name: Git Ref
 long: true
 all: true
 abbrev: 16

common/text_sensor/uptime.yaml

@@ -1,3 +1,3 @@
 ---
 platform: uptime
-name: ${name} Uptime
+name: Uptime

common/text_sensor/version.yaml

@@ -1,3 +1,3 @@
 ---
 platform: version
-name: "${name} Version"
+name: Version

common/text_sensor/wifi_info.yaml

@@ -1,17 +1,19 @@
 ---
 platform: wifi_info
 ip_address:
-  name: ${name} IP Address
+  name: IP Address
   icon: mdi:ip-network
   address_1:
-    name: ${name} IP Address 1
+    name: IP Address 1
+    icon: mdi:ip-network
   address_2:
-    name: ${name} IP Address 2
+    name: IP Address 2
+    icon: mdi:ip-network
 #ssid:
-#  name: ${name} SSID
+#  name: SSID
 #bssid:
-#  name: ${name} BSSID
+#  name: BSSID
 mac_address:
-  name: ${name} MAC
+  name: MAC
 #scan_results:
-#  name: ${name} Latest Scan Results
+#  name: Latest Scan Results

mcu-air-office-r.yaml

@@ -1,12 +1,13 @@
 substitutions:
   device: air-office-r
-  name: Office R Air Quality Monitor
+  name: Office R Air
   name_short: Office R
   area: Office R
   comment: "${area} | AirQ Monitoring"
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   
@@ -15,11 +16,13 @@ esp32:
   # board: m5stamp-pico
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.12
+#    version: 5.3.1
+#    platform_version: 6.9.0
 
-external_components:
-  - source: components
+# external_components:
+#   - source: components
 
 packages:
   common: !include common/common.yaml
@@ -50,21 +53,19 @@ uart:
 
 light:
   - platform: esp32_rmt_led_strip
-    # name: "${name} LED"
+    # name: LED
     id: neo
     rgb_order: GRB
     pin: 27
     num_leds: 1
-    # rmt_channel: 0
     chipset: ws2812
     restore_mode: ALWAYS_OFF
   - platform: esp32_rmt_led_strip
-    name: "${name} NEO"
+    name: NEO
     id: neo_strip
     rgb_order: GRB
     pin: 25
     num_leds: 7
-    # rmt_channel: 1
     chipset: ws2812
     restore_mode: ALWAYS_OFF
     effects:
@@ -116,4 +117,4 @@ sensor:
     uart_id: particle_uart
     update_interval: 20s
     pm_2_5:
-      name: "${name_short} Particulate Matter 2.5µm Concentration"
+      name: Particulate Matter 2.5µm Concentration

mcu-atoms3.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   platformio_options:
@@ -27,8 +28,8 @@ esp32:
     # version: dev
     # version: 5.1.2
     # platform_version: 6.6.0
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.3
+    platform_version: 53.03.12
     # type: arduino
 
 pcf8574:
@@ -56,7 +57,7 @@ web_server:
 
 light:
   - platform: esp32_rmt_led_strip
-    name: "${name} LED"
+    name: LED
     id: neo
     rgb_order: GRB
     pin: 2
@@ -67,12 +68,12 @@ light:
 
 text:
   - platform: template
-    name: "${name} Test Text"
+    name: Test Text
     # id: "it_2"
     icon: "mdi:text"
     optimistic: true
     internal: false
-    initial_value: "Welcome ESPHOME"
+    initial_value: "Welcome ESPHOME - #{name}"
     restore_value: true
     mode: text
     # max_restore_data_length: 24
@@ -206,27 +207,27 @@ m5stack_4relay:
 
 switch:
   - platform: m5stack_4relay
-    name: ${name} Relay 1
+    name: Relay 1
     id: relay_1
     channel: 1
     # interlock: &interlock_group_1 [relay_1, relay_2]
     # interlock_wait_time: 1s
     m5stack_4relay_id: m5stack_relay_1
   - platform: m5stack_4relay
-    name: ${name} Relay 2
+    name: Relay 2
     id: relay_2
     channel: 2
     # interlock: *interlock_group_1
     # interlock_wait_time: 1s
     m5stack_4relay_id: m5stack_relay_1
   - platform: m5stack_4relay
-    name: ${name} Relay 3
+    name: elay 3
     id: relay_3
     channel: 3
     # interlock: &interlock_group_2 [relay_3, relay_4]
     m5stack_4relay_id: m5stack_relay_1
   - platform: m5stack_4relay
-    name: ${name} Relay 4
+    name: Relay 4
     id: relay_4
     channel: 4
     # interlock: *interlock_group_2
@@ -246,7 +247,7 @@ spi:
 
 binary_sensor:
   - platform: gpio
-    name: ${name} Button
+    name: Button
     pin:
       number: 41
       inverted: true
@@ -394,9 +395,9 @@ sensor:
     i2c_id: i2c_main
     address: 0x44
     temperature:
-      name: "TEST Temperature"
+      name: TEST Temperature
     humidity:
-      name: "TEST Humidity"
+      name: TEST Humidity
     update_interval: 10s
   - platform: mpu6886
     address: 0x68
@@ -414,7 +415,7 @@ sensor:
     # gyro_z:
     #   name: "${name} MPU6886 Gyro z"
     temperature:
-      name: "${name} Temperature"
+      name: Temperature
       id: blabla
   - platform: homeassistant
     id: test_humidity
@@ -437,22 +438,22 @@ sensor:
   #   resolution: 12
   - platform: dallas_temp
     address: 0xdb041750eae2ff28
-    name: "${name} Dallas Temp 1"
+    name: Dallas Temp 1
     one_wire_id: hub_1
     update_interval: 10s
   - platform: dallas_temp
     address: 0xb2041750cf1aff28
-    name: "${name} Dallas Temp 2"
+    name: Dallas Temp 2
     one_wire_id: hub_1
     update_interval: 30s
   - platform: dallas_temp
     address: 0xcd01191eb8b07128
-    name: "${name} Dallas Temp 3"
+    name: Dallas Temp 3
     one_wire_id: hub_1
     update_interval: 45s
   - platform: dallas_temp
     address: 0x5a01191ef3375b28
-    name: "${name} Dallas Temp 4"
+    name: Dallas Temp 4
     one_wire_id: hub_1
 
 time:

mcu-basement-2.yaml

@@ -7,6 +7,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 
@@ -31,12 +32,12 @@ status_led:
 
 light:
   - platform: binary
-    name: "${name_short} Light"
+    name: Light
     id: light_1
     output: relay_1
     restore_mode: ALWAYS_ON
   - platform: binary
-    name: "${name_short} Workbench Light"
+    name: Workbench Light
     id: light_2
     output: relay_2
     restore_mode: ALWAYS_ON

mcu-basement.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 
@@ -36,7 +37,7 @@ binary_sensor:
       number: 0
       mode: INPUT_PULLUP
       inverted: True
-    name: ${name} Light Switch
+    name: Light Switch
     device_class: light
     on_click:
     - min_length: 50ms
@@ -45,7 +46,7 @@ binary_sensor:
         - homeassistant.service:
             service: light.toggle
             data:
-              entity_id: light.basement_light
+              entity_id: light.mcu_basement_2_light
     - min_length: 351ms
       max_length: 1000ms
       then:
@@ -73,7 +74,7 @@ binary_sensor:
       number: 10
       mode: INPUT_PULLUP
       inverted: true
-    name: ${name} Socket 1 Switch
+    name: Socket 1 Switch
     on_press:
       - switch.toggle: relay_2
   - platform: gpio
@@ -81,7 +82,7 @@ binary_sensor:
       number: 9
       mode: INPUT_PULLUP
       inverted: true
-    name: ${name} Door
+    name: Door
     device_class: door
     filters:
       invert:
@@ -89,11 +90,11 @@ binary_sensor:
       - homeassistant.service:
           service: light.turn_on
           data:
-            entity_id: light.basement_light
+            entity_id: light.mcu_basement_2_light
 
 select:
   - platform: template
-    name: "Sewage Treatment Blower"
+    name: Sewage Treatment Blower
     icon: mdi:hair-dryer-outline
     optimistic: true
     options:
@@ -125,13 +126,13 @@ status_led:
 
 switch:
   - platform: gpio
-    name: "Sewage Treatment Blower"
+    name: Sewage Treatment Blower
     icon: mdi:hair-dryer-outline
     pin: 12
     id: relay_1
     restore_mode: ALWAYS_ON
   - platform: gpio
-    name: ${name} Socket 1
+    name: Socket 1
     icon: mdi:power-socket-fr
     pin: 5
     id: relay_2

mcu-bedroom-lamp-left.yaml

@@ -7,6 +7,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 
@@ -14,8 +15,8 @@ esp32:
   board: esp32doit-devkit-v1
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.11
     sdkconfig_options:
       CONFIG_FREERTOS_UNICORE: y
     advanced:
@@ -172,7 +173,7 @@ ota:
 light:
   - platform: xiaomi_bslamp2
     id: my_light
-    name: ${name}
+    name: Light
     default_transition_length: ${default_transition_length}
 
     # When the brightness changes, update the front panel illumination.
@@ -291,7 +292,7 @@ sensor:
 # The possible light modes are: "off", "rgb", "white" and "night".
 text_sensor:
   - platform: xiaomi_bslamp2
-    # name: ${name} Light Mode
+    # name: Light Mode
     id: my_light_mode
 
 output:

mcu-bedroom-lamp-right.yaml

@@ -7,6 +7,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 
@@ -14,8 +15,8 @@ esp32:
   board: esp32doit-devkit-v1
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.11
     sdkconfig_options:
       CONFIG_FREERTOS_UNICORE: y
     advanced:
@@ -169,7 +170,7 @@ ota:
 light:
   - platform: xiaomi_bslamp2
     id: my_light
-    name: ${name}
+    name: Light
     default_transition_length: ${default_transition_length}
 
     # When the brightness changes, update the front panel illumination.
@@ -272,7 +273,7 @@ sensor:
 # The possible light modes are: "off", "rgb", "white" and "night".
 text_sensor:
   - platform: xiaomi_bslamp2
-    # name: ${name} Light Mode
+    # name: Light Mode
     id: my_light_mode
 
 output:

mcu-c6-test-1.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   # platformio_options:
@@ -40,8 +41,8 @@ esp32:
   flash_size: 16MB
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.11
 
 logger:
   hardware_uart: USB_SERIAL_JTAG
@@ -54,7 +55,7 @@ logger:
 
 light:
   - platform: esp32_rmt_led_strip
-    name: "${name} LED"
+    name: LED
     id: led
     rgb_order: GRB
     pin: 8

mcu-c6-test-2.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   # platformio_options:
@@ -40,8 +41,8 @@ esp32:
   flash_size: 16MB
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.11
 
 logger:
   hardware_uart: USB_SERIAL_JTAG
@@ -54,7 +55,7 @@ logger:
 
 light:
   - platform: esp32_rmt_led_strip
-    name: "${name} LED"
+    name: LED
     id: led
     rgb_order: GRB
     pin: 8

mcu-cam-1.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 
@@ -27,7 +28,7 @@ packages:
 #     components: [ esp32_camera ]
 
 esp32_camera:
-  name: My Camera
+  name: Camera
   external_clock:
     pin: 0
     frequency: 20MHz
@@ -45,7 +46,7 @@ switch:
     pin: 32
     # restore_mode: ALWAYS_ON
     # id: "cam_power_down"
-    name: "${name} Enable CAM"
+    name: Enable
 
 # esp32_camera_web_server:
 #   - port: 8080

mcu-can-node-1.yaml

@@ -2,10 +2,11 @@ substitutions:
   device: can-node-1
   name: CAN Node 1
   area: DEV
-  comment: "${area} | CANOpen"
+  comment: "${area} | CANopen"
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 
@@ -13,12 +14,14 @@ esp32:
   board: esp32dev
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    # version: 5.3.2
+    # platform_version: 53.03.11
 
 external_components:
   - source: github://mrk-its/esphome-canopen@dev
     refresh: 1h
+  - source: github://mrk-its/esphome-canbus-udp-multicast@dev
+    refresh: 1h
 
 packages:
   common: !include common/common.yaml
@@ -28,65 +31,94 @@ canbus:
     id: can_bus
     rx_pin: 22
     tx_pin: 23
-    can_id: 0
-    bit_rate: 125kbps
+    can_id: 1
+    bit_rate: 500kbps
 
 canopen:
-  id: can_gate
+  id: can_open
   canbus_id: can_bus
   node_id: 1
   entities:
-    - id: boot
-      index: 1
-      tpdo: 0
-    - id: blue_led
-      index: 2
-      tpdo: 0
-    - id: uptime_sensor
-      index: 3
-      tpdo: 0
-    - id: cover1
-      index: 4
-      tpdo: 1
-    # - id: cover2
-    #   index: 5
-    #   tpdo: 1
+    - index: 1
+      id: light1_state
+      rpdo:
+        - node_id: 2
+          tpdo: 0
+          offset: 0
+          cmd: 0
 
-sensor:
-  - platform: uptime
-    id: uptime_sensor
-    name: "${name} Uptime"
-    update_interval: 5sec
-    internal: true
+    - index: 2
+      id: light1_brightness
+      size: 1
+      min_value: 0.0
+      max_value: 1.0
+      rpdo:
+        - node_id: 2
+          tpdo: 0
+          offset: 1
+          cmd: 0
+
+    - index: 3
+      id: light2_state
+      rpdo:
+        - node_id: 2
+          tpdo: 0
+          offset: 3
+          cmd: 0
+
+    - index: 4
+      id: light2_brightness
+      size: 1
+      min_value: 0.0
+      max_value: 1.0
+      rpdo:
+        - node_id: 2
+          tpdo: 0
+          offset: 4
+          cmd: 0
 
 binary_sensor:
+  - platform: template
+    id: light1_state
+    name: Light 1 State
+  - platform: template
+    id: light2_state
+    name: Light 2 State
+
+  - platform: template
+    id: light1_state_cmd
+
   - platform: gpio
-    name: "${name} Boot"
-    id: boot
-    internal: true
+    name: Boot
+    id: boot_button
     pin:
       number: 0
       inverted: true
+      mode:
+        input: true
+        pullup: true
+    on_press:
+      then:
+        - lambda: |-
+            bool state = id(light1_state).state || id(light2_state).state;
+
+            // send command to entity #1 (light) on node #2
+            id(can_open).send_entity_cmd(2, 1, !state);
+
+            // send command to entity #2 (light2) on node #2
+            id(can_open).send_entity_cmd(2, 2, !state);
+
+sensor:
+  - platform: template
+    id: light1_brightness
+    name: Light 1 Brightness
+  - platform: template
+    id: light2_brightness
+    name: Light 2 Brightness
 
 switch:
   - platform: gpio
-    name: "${name} Led"
+    name: LED
     id: blue_led
     internal: true
     pin: 2
-
-cover:
-  - platform: time_based
-    name: "${name} Cover"
-    id: cover1
-    internal: true
-    device_class: shutter
-    has_built_in_endstop: true
-    open_action:
-      - logger.log: open_action
-    open_duration: 10s
-    close_action:
-      - logger.log: close_action
-    close_duration: 10s
-    stop_action:
-      - logger.log: stop_action

mcu-can-node-2.yaml

@@ -2,10 +2,11 @@ substitutions:
   device: can-node-2
   name: CAN Node 2
   area: DEV
-  comment: "${area} | CANOpen"
+  comment: "${area} | CANopen"
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 
@@ -13,12 +14,14 @@ esp32:
   board: esp32dev
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    # version: 5.3.2
+    # platform_version: 53.03.11
 
 external_components:
   - source: github://mrk-its/esphome-canopen@dev
     refresh: 1h
+  - source: github://mrk-its/esphome-canbus-udp-multicast@dev
+    refresh: 1h
 
 packages:
   common: !include common/common.yaml
@@ -28,65 +31,108 @@ canbus:
     id: can_bus
     rx_pin: 22
     tx_pin: 23
-    can_id: 0
-    bit_rate: 125kbps
+    can_id: 2
+    bit_rate: 500kbps
 
 canopen:
-  id: can_gate
+  id: can_open
   canbus_id: can_bus
   node_id: 2
   entities:
-    - id: boot
-      index: 1
+    - index: 1
+      id: light1
       tpdo: 0
-    - id: blue_led
-      index: 2
-      tpdo: 0
-    - id: uptime_sensor
-      index: 3
-      tpdo: 0
-    - id: cover1
-      index: 4
-      tpdo: 1
-    # - id: cover2
-    #   index: 5
-    #   tpdo: 1
 
-sensor:
-  - platform: uptime
-    id: uptime_sensor
-    name: "${name} Uptime"
-    update_interval: 5sec
-    internal: true
+    - index: 2
+      id: light2
+      tpdo: 0
+
+    - index: 3
+      id: light3
+      tpdo: 0
+
+output:
+  - platform: template
+    id: cw_output1
+    type: float
+    write_action:
+      - logger.log:
+          format: "output1: %f"
+          args: ['state']
+
+  - platform: template
+    id: ww_output1
+    type: float
+    write_action:
+      - logger.log:
+          format: "output2: %f"
+          args: ['state']
+
+  - platform: template
+    id: output2
+    type: float
+    write_action:
+      - logger.log:
+          format: "output1: %f"
+          args: ['state']
+
+  - platform: template
+    id: output3
+    type: float
+    write_action:
+      - logger.log:
+          format: "output1: %f"
+          args: ['state']
+
+light:
+  - platform: cwww
+    id: light1
+    name: Light 1
+    cold_white: cw_output1
+    warm_white: ww_output1
+    cold_white_color_temperature: 6536 K
+    warm_white_color_temperature: 2000 K
+    constant_brightness: false
+    default_transition_length: 0s
+
+  - platform: monochromatic
+    id: light2
+    name: Light 2
+    output: output2
+    default_transition_length: 0s
+
+  - platform: binary
+    id: light3
+    name: Light 3
+    output: output3
+
+
+## LIGHTENING
+i2c:
+  sda: 17
+  scl: 18
+  scan: true
+  # frequency: 100kHz
+
+as3935_i2c:
+  irq_pin: 19
+  spike_rejection: 4
 
 binary_sensor:
-  - platform: gpio
-    name: "${name} Boot"
-    id: boot
-    internal: true
-    pin:
-      number: 0
-      inverted: true
+  - platform: as3935
+    name: Storm Alert
 
-switch:
-  - platform: gpio
-    name: "${name} Led"
-    id: blue_led
-    internal: true
-    pin: 2
+sensor:
+  - platform: as3935
+    lightning_energy:
+      name: Energy
+    distance:
+      name: Storm Distance
 
-cover:
-  - platform: time_based
-    name: "${name} Cover"
-    id: cover1
-    internal: true
-    device_class: shutter
-    has_built_in_endstop: true
-    open_action:
-      - logger.log: open_action
-    open_duration: 10s
-    close_action:
-      - logger.log: close_action
-    close_duration: 10s
-    stop_action:
-      - logger.log: stop_action
+# logger:
+#   level: VERY_VERBOSE
+#   logs:
+#     canbus: DEBUG
+#     canopen: DEBUG
+#     can_driver: DEBUG
+#     timer_driver: DEBUG

mcu-cec-bedroom.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 
@@ -14,8 +15,8 @@ esp32:
   framework:
     # type: arduino
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.11
 
 external_components:
   # - source: github://pr#3017
@@ -66,7 +67,7 @@ binary_sensor:
 
 light:
   - platform: esp32_rmt_led_strip
-    name: "${name} LED"
+    name: LED
     id: led
     rgb_order: GRB
     pin: 27

mcu-clock-1.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   platformio_options:
@@ -16,8 +17,8 @@ esp32:
   variant: esp32c3
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.3
+    platform_version: 53.03.12
 
 packages:
   common: !include common/common.yaml
@@ -155,7 +156,7 @@ sensor:
 
 switch:
   - platform: template
-    name: "${name} Alarm"
+    name: Alarm
     optimistic: true
     turn_on_action:
       - globals.set:

mcu-clock-living-room.yaml

@@ -0,0 +1,173 @@
+substitutions:
+  device: clock-living-room
+  name: Living room Clock
+  area: Living Room / Kitchen
+  comment: "${area}: TV Rack Clock"
+
+esphome:
+  name: mcu-${device}
+  friendly_name: ${name}
+  area: ${area}
+  comment: ${comment}
+
+esp32:
+  board: m5stack-atom
+  framework:
+    type: esp-idf
+    # version: 5.3.2
+    # platform_version: 53.03.12
+
+external_components:
+  - source:
+      type: git
+      url: https://github.com/trip5/esphome-tm1650
+      ref: main
+    refresh: 60s
+    components: [ tm1650 ]
+
+packages:
+  common: !include common/common.yaml
+
+# https://github.com/granadaxronos/120-SONG_NOKIA_RTTTL_RINGTONE_PLAYER_FOR_ARDUINO_UNO/blob/master/RTTTL_PLAYER/songs.h
+api:
+  services:
+    - service: play_rtttl
+      variables:
+        song: string
+      then:
+        - rtttl.play:
+            rtttl: !lambda 'return song;'
+
+i2c:
+  id: i2c_main
+  sda: 32
+  scl: 33
+  scan: true #false
+  frequency: 100kHz
+
+globals:
+  - id: alarm_id
+    type: bool
+    restore_value: no
+    initial_value: "false"
+
+time:
+  - platform: homeassistant
+    id: ha_time
+    timezone: Europe/Bratislava
+
+binary_sensor:
+  - platform: gpio
+    name: Button
+    pin:
+      number: 39
+      inverted: true
+
+display:
+  - platform: tm1650
+    id: tm1650_display
+    i2c_id: i2c_main
+    # clk_pin: 4
+    # dio_pin: 5
+    update_interval: 500ms
+    # intensity: 0
+    lambda: |-
+      static int i = 0;
+      i++;
+      if (id(alarm_id)) {
+        if ((i % 2) == 0)
+          it.print("8 8 ");
+        else
+          it.print(" 8 8");      
+      } else {
+        if (((i / 10) % 2) == 0) {
+          //it.set_intensity(7);
+          if ((i % 2) == 0)
+            it.strftime("%H.%M", id(ha_time).now());
+          else
+            it.strftime("%H%M", id(ha_time).now());
+        } else {
+          //it.set_intensity(1);
+          it.printf("%.0f~C", id(temperature).state);
+        }
+      }
+
+light:
+  - platform: esp32_rmt_led_strip
+    name: LED
+    id: led
+    rgb_order: GRB
+    pin: 27
+    num_leds: 1
+    chipset: ws2812
+    restore_mode: ALWAYS_OFF
+    effects:
+      # Use default parameters:
+      - random:
+      # Customize parameters
+      - random:
+          name: "My Slow Random Effect"
+          transition_length: 30s
+          update_interval: 30s
+      - random:
+          name: "My Fast Random Effect"
+          transition_length: 4s
+          update_interval: 5s
+      - strobe:
+      - strobe:
+          name: Strobe Effect With Custom Values
+          colors:
+            - state: True
+              brightness: 100%
+              red: 100%
+              green: 90%
+              blue: 0%
+              duration: 500ms
+            - state: False
+              duration: 250ms
+            - state: True
+              brightness: 100%
+              red: 0%
+              green: 100%
+              blue: 0%
+              duration: 500ms
+      - flicker:
+      - flicker:
+          name: Flicker Effect With Custom Values
+          alpha: 95%
+          intensity: 1.5%
+      - addressable_rainbow:
+      - addressable_rainbow:
+          name: Rainbow Effect With Custom Values
+          speed: 10
+          width: 50
+      - addressable_scan:
+      - addressable_scan:
+          name: Scan Effect With Custom Values
+          move_interval: 100ms
+
+output:
+  - platform: ledc
+    pin: 25
+    id: rtttl_out
+
+rtttl:
+  output: rtttl_out
+
+sensor:
+  - platform: homeassistant
+    id: temperature
+    entity_id: sensor.zigbee_outside_temperature
+
+switch:
+  - platform: template
+    name: Alarm
+    optimistic: true
+    turn_on_action:
+      - globals.set:
+          id: alarm_id
+          value: 'true'
+    turn_off_action:
+      - globals.set:
+          id: alarm_id
+          value: 'false'

mcu-desk-lamp.yaml

@@ -1,11 +1,12 @@
 substitutions:
   device: desk-lamp
-  name: Mi Desk Lamp
+  name: Desk Lamp
   area: Room
   comment: "${area} | Desk lamp"
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 
@@ -13,8 +14,8 @@ esp32:
   board: m5stack-atom
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.11
 
 # external_components:
 #   - source: github://pr#7958
@@ -49,7 +50,7 @@ binary_sensor:
 
 light:
   - platform: cwww
-    name: "${name} Light"
+    name: Light
     id: mi_desk_light
     gamma_correct: 1
     default_transition_length: 100ms

mcu-dev-temp.yaml

@@ -1,36 +0,0 @@
-substitutions:
-  device: dev-temp
-  name: Dev Temp
-  comment: "DEV"
-  
-esphome:
-  name: mcu-${device}
-  comment: ${comment}
-
-esp32:
-  board: esp32doit-devkit-v1
-  framework:
-  #   type: arduino
-    type: esp-idf
-
-external_components:
-  - source: components
-
-packages:
-  common: !include common/common.yaml
-
-switch:
-  - platform: gpio
-    pin: GPIO27
-    id: sensor_power
-    restore_mode: ALWAYS_ON
-
-one_wire:
-  - platform: gpio
-    pin: GPIO25
-
-sensor:
-  - platform: dallas_temp
-    name: $name Dallas
-    id: temp
-    update_interval: 10 s

mcu-dimmer.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   on_loop:
@@ -33,8 +34,8 @@ esp32:
   board: m5stack-atom
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.12
 
 external_components:
   - source: github://pr#7072
@@ -51,7 +52,7 @@ light:
     name: Exercise Room Fan
     default_transition_length: 10s
   - platform: esp32_rmt_led_strip
-    name: "${name} LED"
+    name: LED
     id: led
     rgb_order: GRB
     pin: 27

mcu-echo-1.yaml

@@ -7,6 +7,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 
@@ -60,7 +61,7 @@ api:
 
 binary_sensor:
   - platform: gpio
-    name: ${name} Button
+    name: Button
     pin:
       number: 39
       inverted: true
@@ -77,7 +78,7 @@ light:
   #   id: status_led_id
   #   output: status_led_output
   - platform: esp32_rmt_led_strip
-    name: "${name} LED"
+    name: LED
     id: neo_buildin
     rgb_order: GRB
     pin: 27

mcu-echo.yaml

@@ -7,6 +7,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 
@@ -15,8 +16,8 @@ esp32:
   framework:
     # type: arduino
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.11
 
 external_components:
   - source: components
@@ -48,13 +49,13 @@ i2c:
 
 binary_sensor:
   # - platform: gpio
-  #   name: ${name} On-Board Button
+  #   name: On-Board Button
   #   id: button_buildin
   #   pin:
   #     number: 39
   #     inverted: true
   - platform: gpio
-    name: ${name} Button
+    name: Button
     id: button_ext
     pin:
       number: 12
@@ -72,10 +73,10 @@ light:
   #   pin: 27
   #   variant: WS2812
   #   num_leds: 1
-  #   name: "${name} On-Board LED"
+  #   name: On-Board LED"
   #   id: neo_buildin
   - platform: rgb
-    name: "${name} Light"
+    name: Light
     id: led_light
     red: led_red
     green: led_green
@@ -130,7 +131,7 @@ speaker:
 media_player:
   - platform: speaker
     id: media_out
-    name: ${name} Player
+    name: Player
     media_pipeline:
         speaker: media_spk_resampling_input
     announcement_pipeline:

mcu-eworkbench.yaml

@@ -5,6 +5,7 @@ substitutions:
   
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   comment: ${comment}
   platformio_options:
     board_build.flash_mode: dio
@@ -14,8 +15,8 @@ esp32:
   variant: esp32c3
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.11
 
 packages:
   common: !include common/common.yaml

mcu-fireplace-old.yaml

@@ -1,48 +0,0 @@
-substitutions:
-  device: fireplace-old
-  name: Heating Fireplace
-  comment: "OBSOLETE | Ground floor, Kitchen: Fireplace monitoring for heating"
-
-esphome:
-  name: mcu-${device}
-  comment: ${comment}
-
-esp8266:
-  board: esp01_1m
-
-# wifi:
-#   use_address: mcu-fireplace.local
-
-packages:
-  common: !include common/common_esp8266.yaml
-
-one_wire:
-  - platform: gpio
-    pin: 4
-
-binary_sensor:
-  - platform: template
-    name: "${name} Fire"
-    lambda: |-
-      if (id(heating_fireplace_temperature).state > 37.5) {
-        return true;
-      } else {
-        return false;
-      }
-
-sensor:
-  - platform: dallas_temp
-    address: 0x6203168B32A7FF28
-    # index: 0
-    name: "${name}"
-    id: 'heating_fireplace_temperature'
-  - platform: dht
-    pin: 14
-    temperature:
-      name: "Kitchen Temperature"
-      id: 'kitchen_temperature'
-    humidity:
-      name: "Kitchen Humidity"
-      id: 'kitchen_humidity'
-    update_interval: 60s
-    model: si7021

mcu-fireplace.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 
@@ -13,8 +14,8 @@ esp32:
   board: m5stack-atom
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.11
 
 external_components:
   - source: github://mknjc/esphome@ds248x
@@ -78,12 +79,12 @@ pca9554:
 
 binary_sensor:
   - platform: gpio
-    name: "${name} Status Button"
+    name: Status Button
     filters:
       - invert:
     pin: 39
   - platform: template
-    name: "${name} Fire"
+    name: Fire
     lambda: |-
       if (id(heating_fireplace_temperature).state > 37.5) {
         return true;
@@ -91,7 +92,7 @@ binary_sensor:
         return false;
       }
   - platform: gpio
-    name: "${name} Pump"
+    name: Pump
     id: off_peak_status
     pin:
       pca9554: pca9554_module
@@ -104,7 +105,7 @@ sensor:
   - platform: ds248x
     address: 0x6203168B32A7FF28
     # index: 0
-    name: "${name}"
+    name: Temperature
     id: 'heating_fireplace_temperature'
 #   - platform: dht
 #     pin: 14

mcu-gate.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 
@@ -13,8 +14,8 @@ esp32:
   board: m5stack-atom
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.11
 
 external_components:
   - source: components
@@ -39,12 +40,12 @@ packages:
 
 button:
   - platform: output
-    name: "${name} Open"
+    name: Open
     id: gate_open
     output: relay_1
     duration: 200ms
   - platform: output
-    name: "${name} Close"
+    name: Close
     id: gate_close
     output: relay_2
     duration: 200ms
@@ -59,40 +60,40 @@ output:
 
 switch:
   - platform: template
-    name: "${name} Open"
+    name: Open
     turn_on_action:
       - button.press: gate_open
   - platform: template
-    name: "${name} Close"
+    name: Close
     turn_on_action:
       - button.press: gate_close
   - platform: template
-    name: "${name} Auto Open"
+    name: Auto Open
     id: auto_open
     optimistic: true
     restore_mode: RESTORE_DEFAULT_ON
   - platform: template
-    name: "${name} Auto Close"
+    name: Auto Close
     id: auto_close
     optimistic: true
     restore_mode: RESTORE_DEFAULT_ON
   - platform: template
-    name: "${name} Enable Auris"
+    name: Enable Auris
     id: enable_auris
     optimistic: true
     restore_mode: RESTORE_DEFAULT_ON
   - platform: template
-    name: "${name} Enable Yaris"
+    name: Enable Yaris
     id: enable_yaris
     optimistic: true
     restore_mode: RESTORE_DEFAULT_ON
   - platform: template
-    name: "${name} Enable Honda PCX125"
+    name: Enable Honda PCX125
     id: enable_pcx125
     optimistic: true
     restore_mode: RESTORE_DEFAULT_ON
   - platform: template
-    name: "${name} Enable Suzuki DL650"
+    name: Enable Suzuki DL650
     id: enable_dl650
     optimistic: true
     restore_mode: RESTORE_DEFAULT_ON
@@ -275,7 +276,7 @@ binary_sensor:
 
 select:
   - platform: template
-    name: Gate
+    name: State
     id: gate_state
     options:
      - Open

mcu-gateway.yaml

@@ -1,22 +1,25 @@
 substitutions:
   device: gateway
   name: Gateway
-  comment: "DEV | BLE Proxy, Modbus"
-  
+  area: DEV
+  comment: "${area} | BLE Proxy, Modbus"
+
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
+  area: ${area}
   comment: ${comment}
 
 esp32:
   board: esp32doit-devkit-v1
   framework:
-    # version: 5.1.2
-    # platform_version: 6.6.0
+    version: 5.3.2
+    platform_version: 53.03.11
     type: esp-idf
 
-# external_components:
-  # - source: github://pr#4062
-  #   components: ethernet
+external_components:
+  - source: github://pr#8457
+    components: ethernet
   # - source: github://pr#4080
   #   components: [lcd_pcf8574, lcd_base]
   # - source: github://pr#3564
@@ -72,10 +75,10 @@ i2c:
   #   subnet: 255.255.255.0
 
 
-ethernet:
+# ethernet:
   # use_address: 10.17.241.254
   # use_address: 10.17.241.98
-  use_address: mcu-gateway.local
+  # use_address: mcu-gateway.local
 
 uart:
   id: uart_modbus
@@ -108,7 +111,7 @@ sensor:
   - platform: modbus_controller
     modbus_controller_id: modbus_temp_1
     id: temp_1
-    name: "${name} Temperature 1"
+    name: Temperature 1
     address: 0
     unit_of_measurement: "°C"
     register_type: read
@@ -120,7 +123,7 @@ sensor:
   - platform: modbus_controller
     modbus_controller_id: modbus_temp_1
     id: hum_1
-    name: "${name} Humidity 1"
+    name: Humidity 1
     address: 1
     unit_of_measurement: "%"
     register_type: read
@@ -131,7 +134,7 @@ sensor:
   - platform: modbus_controller
     modbus_controller_id: modbus_temp_2
     id: temp_2
-    name: "${name} Temperature 2"
+    name: Temperature 2
     address: 0
     unit_of_measurement: "°C"
     register_type: read
@@ -143,7 +146,7 @@ sensor:
   - platform: modbus_controller
     modbus_controller_id: modbus_temp_2
     id: hum_2
-    name: "${name} Humidity 2"
+    name: Humidity 2
     address: 1
     unit_of_measurement: "%"
     register_type: read
@@ -153,25 +156,25 @@ sensor:
       - multiply: 0.1
   # - platform: bmp085
   #   temperature:
-  #     name: "BMP180 Temperature"
+  #     name: BMP180 Temperature
   #   pressure:
-  #     name: "BMP180 Pressure"
+  #     name: BMP180 Pressure
   #   address: 0x77
   #   update_interval: 60s
   # - platform: bme280
   #   temperature:
-  #     name: "BME280 Temperature"
+  #     name: BME280 Temperature
   #     oversampling: 16x
   #   pressure:
-  #     name: "BME280 Pressure"
+  #     name: BME280 Pressure
   #   humidity:
-  #     name: "BME280 Humidity"
+  #     name: BME280 Humidity
   #   address: 0x76
   #   update_interval: 60s
   - platform: modbus_controller
     modbus_controller_id: modbus_adc_1
     id: adc_1_1
-    name: "Solar Pressure"
+    name: Solar Pressure
     address: 0
     unit_of_measurement: "MPa"
     register_type: holding
@@ -186,7 +189,7 @@ sensor:
 switch:
 - platform: modbus_controller
   modbus_controller_id: modbus_adc_1
-  name: "Readress MODBUS"
+  name: Readress MODBUS
   register_type: holding
   address: 0x00FD
   entity_category: config

mcu-heating.yaml

@@ -7,6 +7,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 
@@ -14,8 +15,8 @@ esp32:
   board: m5stack-atom
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.11
 
 external_components:
   - source: github://mknjc/esphome@ds248x

mcu-irrigation-1.yaml

@@ -1,226 +0,0 @@
-substitutions:
-  device: irrigation-1
-  name: Irrigation A
-  comment: "OBSOLETE | Outside, Well: Irrigation system"
-
-esphome:
-  name: mcu-${device}
-  comment: ${comment}
-  # on_boot:
-  #   priority: -10
-  #   then:
-  #     - switch.turn_off: relay_1
-  #     - delay: 2s
-  #     - switch.turn_off: relay_2
-  #     - delay: 2s
-  #     - switch.turn_off: relay_3
-  #     - delay: 2s
-  #     - switch.turn_off: relay_4
-  #     - delay: 2s
-  #     - switch.turn_off: relay_5
-
-esp8266:
-  board: esp01_1m
-
-packages:
-  common: !include common/common_esp8266.yaml
-  
-# api:
-#   services:
-#     - service: program_morning
-#       then:
-#         - switch.turn_on: relay_1
-#         - delay: 10minutes
-#         - switch.turn_off: relay_1
-#         - delay: 1minutes
-#         - switch.turn_on: relay_2
-#         - delay: 10minutes
-#         - switch.turn_off: relay_2
-#         - delay: 1minutes
-#         - switch.turn_on: relay_3
-#         - delay: 5minutes
-#         # - switch.turn_on: relay_4
-#         # - delay: 40minutes
-#         - switch.turn_off: relay_3
-#         - delay: 1minutes
-#         - switch.turn_on: relay_1
-#         - delay: 10minutes
-#         - switch.turn_off: relay_1
-#         - delay: 1minutes
-#         - switch.turn_on: relay_2
-#         - delay: 10minutes
-#         - switch.turn_off: relay_2
-#         - delay: 1minutes
-#         - switch.turn_on: relay_3
-#         - delay: 5minutes
-#         # - switch.turn_on: relay_4
-#         # - delay: 40minutes
-#         - switch.turn_off: relay_3
-#     - service: program_grass
-#       then:
-#         - switch.turn_on: relay_1
-#         - delay: 5minutes
-#         - switch.turn_off: relay_1
-#         - delay: 1minutes
-#         - switch.turn_on: relay_2
-#         - delay: 5minutes
-#         - switch.turn_off: relay_2
-#     - service: patio
-#       then:
-#         - switch.turn_on: relay_5
-#         - delay: 30sec
-#         - switch.turn_off: relay_5
-
-i2c:
-  sda: 3
-  scl: 1
-  scan: true #false
-
-# mcp23017:
-#   - id: 'mcp23017_hub'
-#     address: 0x20
-
-pcf8574:
-  - id: 'relay_module'
-    address: 0x20
-    pcf8575: false
-
-# SONOFF 4ch Pro! Not R2!
-# GPIO_KEY1,        // GPIO00 Button 1
-# GPIO_USER,        // GPIO01 Serial RXD and Optional sensor
-# GPIO_USER,        // GPIO02 Optional sensor
-# GPIO_USER,        // GPIO03 Serial TXD and Optional sensor
-# GPIO_REL3,        // GPIO04 Sonoff 4CH Red Led and Relay 3 (0 = Off, 1 = On)
-# GPIO_REL2,        // GPIO05 Sonoff 4CH Red Led and Relay 2 (0 = Off, 1 = On)
-#                   // GPIO06 (SD_CLK   Flash)
-#                   // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
-#                   // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
-# GPIO_KEY2,        // GPIO09 Button 2
-# GPIO_KEY3,        // GPIO10 Button 3
-#                   // GPIO11 (SD_CMD   Flash)
-# GPIO_REL1,        // GPIO12 Red Led and Relay 1 (0 = Off, 1 = On)
-# GPIO_LED1_INV,    // GPIO13 Blue Led (0 = On, 1 = Off) - Link and Power status
-# GPIO_KEY4,        // GPIO14 Button 4
-# GPIO_REL4,        // GPIO15 Red Led and Relay 4 (0 = Off, 1 = On)
-
-# binary_sensor:
-  # - platform: gpio
-  #   pin:
-  #     number: GPIO0
-  #     mode: INPUT_PULLUP
-  #     inverted: True
-  #   name: "Irrigation Button A1"
-  #   id: button_1
-  #   on_press:
-  #     - switch.toggle: relay_1
-  # - platform: gpio
-  #   pin:
-  #     number: GPIO9
-  #     mode: INPUT_PULLUP
-  #     inverted: True
-  #   name: "Irrigation Button A2"
-  #   id: button_2
-  #   on_press:
-  #     - switch.toggle: relay_2
-  # - platform: gpio
-  #   pin:
-  #     number: GPIO10
-  #     mode: INPUT_PULLUP
-  #     inverted: True
-  #   name: "Irrigation Button A3"
-  #   id: button_3
-  #   on_press:
-  #     - switch.toggle: relay_3
-  # - platform: gpio
-  #   pin:
-  #     number: GPIO14
-  #     mode: INPUT_PULLUP
-  #     inverted: True
-  #   name: "Irrigation Button A4"
-  #   id: button_4
-  #   on_press:
-  #     - switch.toggle: relay_4
-
-# sensor:
-  # - platform: dht
-  #   pin: GPIO2
-  #   temperature:
-  #     name: "Well Shaft Temperature"
-  #     id: 'well_temperature'
-  #   humidity:
-  #     name: "Well Shaft Humidity"
-  #     id: 'well_humidity'
-  #   model: 'DHT22'
-  #   update_interval: 60s
-
-# switch:
-#   - platform: gpio
-#     name: "Irrigation Valve A1"
-#     pin: GPIO12
-#     id: relay_1
-#     interlock: &interlock_group [relay_1, relay_2, relay_3, relay_4, relay_5, relay_6, relay_7, relay_8]
-#   - platform: gpio
-#     name: "Irrigation Valve A2"
-#     pin: GPIO5
-#     id: relay_2
-#     interlock: *interlock_group
-#   - platform: gpio
-#     name: "Irrigation Valve A3"
-#     pin: GPIO4
-#     id: relay_3
-#     interlock: *interlock_group
-#   - platform: gpio
-#     name: "Irrigation Valve A4"
-#     pin: GPIO15
-#     id: relay_4
-#     interlock: *interlock_group
-#   - platform: gpio
-#     name: "Irrigation Valve A5"
-#     id: relay_5
-#     interlock: *interlock_group
-#     pin:
-#       pcf8574: relay_module
-#       number: 0
-#       mode: OUTPUT
-#       inverted: true
-#   - platform: gpio
-#     name: "Irrigation Valve A6"
-#     id: relay_6
-#     interlock: *interlock_group
-#     pin:
-#       pcf8574: relay_module
-#       number: 1
-#       mode: OUTPUT
-#       inverted: true
-#   - platform: gpio
-#     name: "Irrigation Valve A7"
-#     id: relay_7
-#     interlock: *interlock_group
-#     pin:
-#       pcf8574: relay_module
-#       number: 2
-#       mode: OUTPUT
-#       inverted: true
-#   - platform: gpio
-#     name: "Irrigation Valve A8"
-#     id: relay_8
-#     interlock: *interlock_group
-#     pin:
-#       pcf8574: relay_module
-#       number: 3
-#       mode: OUTPUT
-#       inverted: true
-      
-# output:
-#   - platform: esp8266_pwm
-#     id: led_blue
-#     pin: GPIO13
-#     inverted: True
-
-# light:
-#   - platform: monochromatic
-#     name: "Irrigation A Blue LED"
-#     output: led_blue
-
-time:
-  - !include common/time/homeassistant.yaml

mcu-kitchen.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   on_boot:
@@ -31,8 +32,8 @@ esp32:
   board: m5stack-atom
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.11
 
 packages:
   common: !include common/common.yaml
@@ -85,14 +86,14 @@ pca9685:
 
 binary_sensor:
   - platform: gpio
-    name: "${name} Status Button"
+    name: Status Button
     filters:
       - invert:
     pin: 39
 
 light:
   # - platform: esp32_rmt_led_strip
-  #   name: "${name} Status Light"
+  #   name: Status Light
   #   id: neo
   #   rgb_order: GRB
   #   pin: 27
@@ -101,7 +102,7 @@ light:
   #   chipset: ws2812
   #   restore_mode: ALWAYS_OFF
   - platform: cwww
-    name: "${name} Worktop Left"
+    name: Worktop Left
     id: light_1
     default_transition_length: 200ms
     restore_mode: ALWAYS_ON
@@ -110,7 +111,7 @@ light:
     cold_white_color_temperature: 6536 K
     warm_white_color_temperature: 2000 K
   - platform: cwww
-    name: "${name} Stove"
+    name: Stove
     id: light_2
     default_transition_length: 200ms
     restore_mode: ALWAYS_ON
@@ -119,7 +120,7 @@ light:
     cold_white_color_temperature: 6536 K
     warm_white_color_temperature: 2000 K
   - platform: cwww
-    name: "${name} Worktop Right"
+    name: Worktop Right
     id: light_3
     default_transition_length: 200ms
     restore_mode: ALWAYS_ON
@@ -128,7 +129,7 @@ light:
     cold_white_color_temperature: 6536 K
     warm_white_color_temperature: 2000 K
   # - platform: cwww
-  #   name: "${name} Light Spare"
+  #   name: Light Spare
   #   id: light_4
   #   default_transition_length: 200ms
   #   restore_mode: ALWAYS_ON

mcu-lightening.yaml

@@ -7,6 +7,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   
@@ -41,7 +42,7 @@ as3935_i2c:
 
 binary_sensor:
 #   - platform: gpio
-#     # name: ${name} Button
+#     # name: Button
 #     pin:
 #       number: 39
 #       inverted: true
@@ -50,7 +51,7 @@ binary_sensor:
 
 light:
   - platform: esp32_rmt_led_strip
-    # name: "${name} LED"
+    # name: LED
     id: neo
     rgb_order: GRB
     pin: 27
@@ -61,7 +62,7 @@ light:
 sensor:
   - platform: as3935
     lightning_energy:
-      name: Lightning Energy
+      name: Energy
     distance:
       name: Storm Distance
 

mcu-lvgl-eworkbench.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   platformio_options:
@@ -20,8 +21,8 @@ esp32:
   flash_size: 16MB
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.11
     sdkconfig_options:
       CONFIG_ESP32S3_DEFAULT_CPU_FREQ_240: y
       CONFIG_ESP32S3_DATA_CACHE_64KB: y
@@ -46,7 +47,7 @@ i2c:
 
 psram:
   mode: octal
-  speed: 120MHz
+  speed: 40MHz
   
 spi:
   id: display_qspi

mcu-lvgl.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   platformio_options:
@@ -18,8 +19,8 @@ esp32:
   flash_size: 16MB
   framework:
     type: esp-idf
-    # version: 5.1.2
-    # platform_version: 6.5.0
+    version: 5.3.2
+    platform_version: 53.03.11
     # Required to achieve sufficient PSRAM bandwidth
     sdkconfig_options:
       CONFIG_ESP32S3_DEFAULT_CPU_FREQ_240: y
@@ -301,10 +302,12 @@ image:
     # mdi:battery-arrow-down-outline
     id: solar_power_icon
     resize: 50x50
+    type: BINARY
 
   - file: mdi:battery-arrow-down-outline
     id: home_battery_icon
     resize: 30x30
+    type: BINARY
 
 lvgl:
   log_level: INFO
@@ -374,8 +377,8 @@ lvgl:
                       color: 0xFFFFFF
                       r_mod: 12 #sets line length by this much difference from the scale default radius
                       value: 50
-                  - img:
-                      id: power_meter_input_img
+                  # - image:
+                  #     id: power_meter_input_img
                   - arc:
                       color: 0xFF3000
                       r_mod: 10 #radius difference from the scale default radius
@@ -439,12 +442,12 @@ lvgl:
               #bg_color: 0xFFFFFF
               #y: -35
               #x: -60
-          - img:
+          - image:
               src: solar_power_icon
               id: img_solar_power
               align: center
-              img_recolor: 0xFFFF00
-              img_recolor_opa: 100% #opacity defaults to 0% = must set this for recolor to take effect
+              image_recolor: 0xFFFF00
+              image_recolor_opa: 100% #opacity defaults to 0% = must set this for recolor to take effect
               #bg_color: 0xFFFFFF
               y: 50
               #x: -60
@@ -482,8 +485,8 @@ lvgl:
                       color: 0xFFFFFF
                       r_mod: 12 #sets line length by this much difference from the scale default radius
                       value: 50
-                  - img:
-                      id: power_meter_input_img2
+                  # - image:
+                  #     id: power_meter_input_img2
                   - arc:
                       color: 0xFF3000
                       r_mod: 10 #radius difference from the scale default radius
@@ -547,12 +550,12 @@ lvgl:
               #bg_color: 0xFFFFFF
               #y: -35
               #x: -60
-          - img:
+          - image:
               src: solar_power_icon
               id: img_solar_power2
               align: center
-              img_recolor: 0xFFFF00
-              img_recolor_opa: 100% #opacity defaults to 0% = must set this for recolor to take effect
+              image_recolor: 0xFFFF00
+              image_recolor_opa: 100% #opacity defaults to 0% = must set this for recolor to take effect
               #bg_color: 0xFFFFFF
               y: 50
               #x: -60
@@ -590,8 +593,8 @@ lvgl:
                       color: 0xFFFFFF
                       r_mod: 12 #sets line length by this much difference from the scale default radius
                       value: 50
-                  - img:
-                      id: power_meter_input_img3
+                  # - image:
+                  #     id: power_meter_input_img3
                   - arc:
                       color: 0xFF3000
                       r_mod: 10 #radius difference from the scale default radius
@@ -655,12 +658,12 @@ lvgl:
               #bg_color: 0xFFFFFF
               #y: -35
               #x: -60
-          - img:
+          - image:
               src: solar_power_icon
               id: img_solar_power3
               align: center
-              img_recolor: 0xFFFF00
-              img_recolor_opa: 100% #opacity defaults to 0% = must set this for recolor to take effect
+              image_recolor: 0xFFFF00
+              image_recolor_opa: 100% #opacity defaults to 0% = must set this for recolor to take effect
               #bg_color: 0xFFFFFF
               y: 50
               #x: -60

mcu-mains-power.yaml

@@ -14,8 +14,8 @@ esp32:
   board: m5stack-atom
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.11
   
 packages:
   common: !include common/common.yaml

mcu-nspanel-bedroom.yaml

@@ -11,6 +11,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   on_boot:
@@ -185,7 +186,7 @@ time:
 
 binary_sensor:
   - platform: gpio
-    name: ${name} Left Button
+    name: Left Button
     pin:
       number: 14
       inverted: true
@@ -197,14 +198,13 @@ binary_sensor:
             root["CustomRecv"] = "event,buttonPress2,navigate.cardGrid_main,button";
 
   - platform: gpio
-    name: ${name} Right Button
+    name: Right Button
     pin:
       number: 27
       inverted: true
     # on_click:
     #   - switch.toggle: relay_2
     on_click:
-
       - homeassistant.service:
           service: light.toggle
           data:
@@ -216,7 +216,7 @@ binary_sensor:
 
 light:
   - platform: binary
-    name: ${name_short} Light
+    name: Light
     id: light_1
     output: relay_1
 
@@ -236,7 +236,7 @@ output:
 
 switch:
   - platform: gpio
-    name: ${name} Screen Power
+    name: Screen Power
     id: screen_power
     entity_category: config
     pin:
@@ -268,7 +268,7 @@ sensor:
       b_constant: 3950
       reference_temperature: 25°C
       reference_resistance: 10kOhm
-    name: "${name_short} Temperature"
+    name: Temperature
     
   - platform: template
     id: room_temperature_id

mcu-nspanel-dev.yaml

@@ -1,7 +1,6 @@
 substitutions:
   device: nspanel-dev
   name: NSPanel DEV
-  name_short: DevPanel
   area: DEV
   comment: "${area} | NSPanel"
   panel_recv_topic: "tele/${device}/RESULT"
@@ -10,6 +9,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   on_boot:
@@ -34,8 +34,8 @@ esp32:
   board: nodemcu-32s
   framework:
     type: esp-idf
-    # version: 5.1.2
-    # platform_version: 6.6.0
+    version: 5.3.2
+    platform_version: 53.03.11
 
 external_components:
   # - source:
@@ -424,7 +424,7 @@ time:
 
 binary_sensor:
   - platform: gpio
-    name: ${name} Left Button
+    name: Left Button
     pin:
       number: 14
       inverted: true
@@ -436,7 +436,7 @@ binary_sensor:
       #       entity_id: switch.gate_open
 
   - platform: gpio
-    name: ${name} Right Button
+    name: Right Button
     pin:
       number: 27
       inverted: true
@@ -455,7 +455,7 @@ output:
 
 switch:
   - platform: gpio
-    name: ${name} Relay 1
+    name: Relay 1
     id: relay_1
     pin:
       number: 22
@@ -470,7 +470,7 @@ switch:
     #       payload: '{"CustomRecv":"event,sleepReached,cardGrid"}'
 
   - platform: gpio
-    name: ${name} Relay 2
+    name: Relay 2
     id: relay_2
     pin:
       number: 19
@@ -485,7 +485,7 @@ switch:
 
   # Turn screen power on/off. Easy way to configure the screen power control, but this should not be used from HA, as all components must be re-initialized afterwards. For lights, names of lights etc. this practically means that the state must change once to happen.
   - platform: gpio
-    name: ${name} Screen Power
+    name: Screen Power
     id: screen_power
     entity_category: config
     pin:
@@ -517,7 +517,7 @@ sensor:
       b_constant: 3950
       reference_temperature: 25°C
       reference_resistance: 10kOhm
-    name: "Living Room Temperature Entry"
+    name: Living Room Temperature Entry
     
   - platform: template
     id: room_temperature_id

mcu-nspanel-fireplace.yaml

@@ -1,7 +1,6 @@
 substitutions:
   device: nspanel-fireplace
   name: Fireplace NSPanel
-  name_short: Fireplace
   area: Living Room / Kitchen
   comment: "${area}, Fireplace | NSPanel"
   panel_recv_topic: "tele/${device}/RESULT"
@@ -10,6 +9,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   on_boot:
@@ -184,7 +184,7 @@ time:
 
 binary_sensor:
   - platform: gpio
-    name: ${name} Left Button
+    name: Left Button
     pin:
       number: 14
       inverted: true
@@ -200,7 +200,7 @@ binary_sensor:
             root["CustomRecv"] = "event,buttonPress2,navigate.cardGrid_main,button";
 
   - platform: gpio
-    name: ${name} Right Button
+    name: Right Button
     pin:
       number: 27
       inverted: true
@@ -236,7 +236,7 @@ switch:
       number: 19
 
   - platform: gpio
-    name: ${name} Screen Power
+    name: Screen Power
     id: screen_power
     entity_category: config
     pin:
@@ -268,7 +268,7 @@ sensor:
       b_constant: 3950
       reference_temperature: 25°C
       reference_resistance: 10kOhm
-    name: "Living Room Temperature Fireplace"
+    name: "Living Room Temperature"
     
   - platform: template
     id: room_temperature_id

mcu-nspanel-office-j.yaml

@@ -1,7 +1,6 @@
 substitutions:
   device: nspanel-office-j
   name: Office J NSPanel
-  name_short: Office J
   area: Office J
   comment: "${area} | NSPanel"
   panel_recv_topic: "tele/${device}/RESULT"
@@ -11,6 +10,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   on_boot:
@@ -190,7 +190,7 @@ time:
 
 binary_sensor:
   # - platform: gpio
-  #   name: ${name} Left Button
+  #   name: Left Button
   #   pin:
   #     number: 14
   #     inverted: true
@@ -198,7 +198,7 @@ binary_sensor:
   #     - switch.toggle: relay_1
 
   # - platform: gpio
-  #   name: ${name} Right Button
+  #   name: Right Button
   #   pin:
   #     number: 27
   #     inverted: true
@@ -210,7 +210,7 @@ binary_sensor:
   #         data:
   #           entity_id: light.office_r_desk_strip
   - platform: gpio
-    name: ${name} Left Button
+    name: Left Button
     pin:
       number: 14
       inverted: true
@@ -222,7 +222,7 @@ binary_sensor:
             root["CustomRecv"] = "event,buttonPress2,navigate.cardGrid_main,button";
 
   - platform: gpio
-    name: ${name} Right Button
+    name: Right Button
     pin:
       number: 27
       inverted: true
@@ -252,16 +252,16 @@ output:
 
 light:
   - platform: binary
-    name: ${name_short} Light
+    name: Light
     id: light_1
     output: relay_1
 #   # - platform: binary
-#   #   name: ${name_full} Relay 2
+#   #   name: Relay 2
 #   #   output: relay_2
 
 switch:
   - platform: gpio
-    name: ${name} Screen Power
+    name: Screen Power
     id: screen_power
     entity_category: config
     pin:
@@ -291,7 +291,7 @@ sensor:
       b_constant: 3950
       reference_temperature: 22°C
       reference_resistance: 10kOhm
-    name: "${name_short} Temperature"
+    name: Temperature
   - platform: template
     id: room_temperature_id
 
@@ -299,7 +299,7 @@ sensor:
 
 # text_sensor:
 #   - platform: ble_scanner
-#     name: "${name_short} BLE Scanner"
+#     name: BLE Scanner
     
 # esp32_ble_beacon:
 #   type: iBeacon

mcu-nspanel-office-r.yaml

@@ -1,7 +1,6 @@
 substitutions:
   device: nspanel-office-r
   name: Office R NSPanel
-  name_short: Office R
   area: Office R
   comment: "${area} | NSPanel"
   panel_recv_topic: "tele/${device}/RESULT"
@@ -11,6 +10,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   on_boot:
@@ -196,7 +196,7 @@ time:
 
 binary_sensor:
   # - platform: gpio
-  #   name: ${name} Left Button
+  #   name: Left Button
   #   pin:
   #     number: 14
   #     inverted: true
@@ -204,7 +204,7 @@ binary_sensor:
   #     - switch.toggle: relay_1
 
   # - platform: gpio
-  #   name: ${name} Right Button
+  #   name: Right Button
   #   pin:
   #     number: 27
   #     inverted: true
@@ -216,7 +216,7 @@ binary_sensor:
   #         data:
   #           entity_id: light.office_r_desk_strip
   - platform: gpio
-    name: ${name} Left Button
+    name: Left Button
     pin:
       number: 14
       inverted: true
@@ -232,7 +232,7 @@ binary_sensor:
       # - lambda: 'id(nspanel_id).send_custom_command("event,buttonPress1,navigate.cardGrid_main,button");'
 
   - platform: gpio
-    name: ${name} Right Button
+    name: Right Button
     pin:
       number: 27
       inverted: true
@@ -260,7 +260,7 @@ output:
 
 light:
   - platform: esp32_rmt_led_strip
-    name: "${name_short} Presence Light"
+    name: Presence Light
     id: neo
     rgb_order: GRB
     pin: 23
@@ -278,26 +278,26 @@ light:
           transition_length: 2s      # defaults to 1s
           update_interval: 2s
   - platform: binary
-    name: ${name_short} Light
+    name: Light
     id: light_1
     output: relay_1
 #   # - platform: binary
-#   #   name: ${name_full} Relay 2
+#   #   name: Relay 2
 #   #   output: relay_2
 
 switch:
   # - platform: gpio
-  #   name: ${name_short} Light
+  #   name: Light
   #   id: relay_1
   #   pin:
   #     number: 22
   - platform: gpio
-    # name: ${name_full} Relay 2
+    # name: Relay 2
     id: relay_2
     pin:
       number: 19
   - platform: gpio
-    name: ${name} Screen Power
+    name: Screen Power
     id: screen_power
     entity_category: config
     pin:
@@ -327,7 +327,7 @@ sensor:
       b_constant: 3950
       reference_temperature: 22°C
       reference_resistance: 10kOhm
-    name: "${name_short} Temperature"
+    name: Temperature
   - platform: template
     id: room_temperature_id
 
@@ -335,7 +335,7 @@ sensor:
 
 # text_sensor:
 #   - platform: ble_scanner
-#     name: "${name_short} BLE Scanner"
+#     name: BLE Scanner
     
 # esp32_ble_beacon:
 #   type: iBeacon

mcu-nspanel-patio.yaml

@@ -1,7 +1,6 @@
 substitutions:
   device: nspanel-patio
   name: Patio NSPanel
-  name_short: Patio
   area: Living Room / Kitchen
   comment: "${area}, Patio | NSPanel"
   panel_recv_topic: "tele/${device}/RESULT"
@@ -10,6 +9,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   on_boot:
@@ -184,7 +184,7 @@ time:
 
 binary_sensor:
   - platform: gpio
-    name: ${name} Left Button
+    name: Left Button
     pin:
       number: 14
       inverted: true
@@ -196,7 +196,7 @@ binary_sensor:
             root["CustomRecv"] = "event,buttonPress2,navigate.cardGrid_main,button";
 
   - platform: gpio
-    name: ${name} Right Button
+    name: Right Button
     pin:
       number: 27
       inverted: true
@@ -208,7 +208,7 @@ binary_sensor:
           - homeassistant.service:
               service: light.toggle
               data:
-                entity_id: light.patio_light
+                entity_id: light.patio_lights
           - mqtt.publish_json:
               topic: $panel_recv_topic
               payload: |-
@@ -230,7 +230,7 @@ switch:
       number: 22
 
   - platform: gpio
-    name: ${name_short} Light MAIN
+    name: Light MAIN
     id: relay_2
     restore_mode: always_on
     entity_category: config
@@ -238,7 +238,7 @@ switch:
       number: 19
       
   - platform: gpio
-    name: ${name} Screen Power
+    name: Screen Power
     id: screen_power
     entity_category: config
     pin:
@@ -270,7 +270,7 @@ sensor:
       b_constant: 3950
       reference_temperature: 25°C
       reference_resistance: 10kOhm
-    name: "Living Room Temperature"
+    name: Living Room Temperature
     
   - platform: template
     id: room_temperature_id

mcu-office-r.yaml

@@ -6,6 +6,7 @@ substitutions:
   
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   platformio_options:
@@ -17,8 +18,8 @@ esp32:
   variant: esp32c3
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.11
 
 packages:
   common: !include common/common.yaml

mcu-patio.yaml

@@ -6,6 +6,7 @@ substitutions:
   
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   on_boot:
@@ -85,14 +86,14 @@ pca9685:
 
 binary_sensor:
   - platform: gpio
-    name: "${name} Status Button"
+    name: Status Button
     filters:
       - invert:
     pin: 39
 
 light:
   # - platform: esp32_rmt_led_strip
-  #   name: "${name} Status Light"
+  #   name: Status Light
   #   id: neo
   #   rgb_order: GRB
   #   pin: 27
@@ -101,7 +102,7 @@ light:
   #   chipset: ws2812
   #   restore_mode: ALWAYS_OFF
   - platform: cwww
-    name: "${name} Light 1"
+    name: Light 1
     id: light_1
     default_transition_length: 200ms
     restore_mode: ALWAYS_ON
@@ -110,7 +111,7 @@ light:
     cold_white_color_temperature: 6536 K
     warm_white_color_temperature: 2000 K
   - platform: cwww
-    name: "${name} Light 2"
+    name: Light 2
     id: light_2
     default_transition_length: 200ms
     restore_mode: ALWAYS_ON
@@ -119,7 +120,7 @@ light:
     cold_white_color_temperature: 6536 K
     warm_white_color_temperature: 2000 K
   - platform: cwww
-    name: "${name} Light 3"
+    name: Light 3
     id: light_3
     default_transition_length: 200ms
     restore_mode: ALWAYS_ON
@@ -128,7 +129,7 @@ light:
     cold_white_color_temperature: 6536 K
     warm_white_color_temperature: 2000 K
   - platform: cwww
-    name: "${name} Light 4"
+    name: Light 4
     id: light_4
     default_transition_length: 200ms
     restore_mode: ALWAYS_ON
@@ -201,6 +202,6 @@ power_supply:
 
 switch:
   - platform: gpio
-    name: "${name} Relay"
+    name: Relay
     id: relay_2
     pin: 19

mcu-pow-1.yaml

@@ -6,6 +6,7 @@ substitutions:
   
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   comment: ${comment}
   on_boot: # Set the initial state of the template switch to the actual relay state. This will NOT change the state.
     priority: 250.0 # Wait until WiFi is connected to allow the sensor some time to settle
@@ -73,7 +74,7 @@ binary_sensor:
     publish_initial_state: true
     internal: true
   - platform: template
-    name: "${name} Load"
+    name: Load
     id: load_on
     lambda: |-
       if (isnan(id(w_sensor).state)) {
@@ -128,17 +129,17 @@ output:
 sensor:
   - platform: cse7766
     current:
-      name: "${name} Current"
+      name: Current
       id: a_sensor
       filters:
         - throttle_average: ${update_interval}
     voltage:
-      name: "${name} Voltage"
+      name: Voltage
       id: v_sensor
       filters:
         - throttle_average: ${update_interval}
     power:
-      name: "${name} Power"
+      name: Power
       id: w_sensor
       filters:
         - throttle_average: ${update_interval}
@@ -150,27 +151,27 @@ sensor:
           then:
             - light.turn_off: switch_led
     energy:
-      name: "${name} Energy"
+      name: Energy
       id: wh_sensor
       filters:
         - throttle_average: ${update_interval}
 
   - platform: total_daily_energy
-    name: "${name} Total Daily Energy"
+    name: Total Daily Energy
     power_id: w_sensor
     filters:
       - multiply: 0.001
     unit_of_measurement: kWh
 
   - platform: template
-    name: "${name} Power Factor"
+    name: Power Factor
     device_class: power_factor
     id: power_factor
     lambda: return id(w_sensor).state / id(v_sensor).state / id(a_sensor).state;
 
 switch:
   - platform: template
-    name: "${name} Relay"
+    name: Relay
     optimistic: true
     id: relay_1
     turn_off_action:

mcu-pow-2.yaml

@@ -6,6 +6,7 @@ substitutions:
   
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   comment: ${comment}
   on_boot: # Set the initial state of the template switch to the actual relay state. This will NOT change the state.
     priority: 250.0 # Wait until WiFi is connected to allow the sensor some time to settle
@@ -73,7 +74,7 @@ binary_sensor:
     publish_initial_state: true
     internal: true
   - platform: template
-    name: "${name} Load"
+    name: Load
     id: load_on
     lambda: |-
       if (isnan(id(w_sensor).state)) {
@@ -128,17 +129,17 @@ output:
 sensor:
   - platform: cse7766
     current:
-      name: "${name} Current"
+      name: Current
       id: a_sensor
       filters:
         - throttle_average: ${update_interval}
     voltage:
-      name: "${name} Voltage"
+      name: Voltage
       id: v_sensor
       filters:
         - throttle_average: ${update_interval}
     power:
-      name: "${name} Power"
+      name: Power
       id: w_sensor
       filters:
         - throttle_average: ${update_interval}
@@ -150,27 +151,27 @@ sensor:
           then:
             - light.turn_off: switch_led
     energy:
-      name: "${name} Energy"
+      name: Energy"
       id: wh_sensor
       filters:
         - throttle_average: ${update_interval}
 
   - platform: total_daily_energy
-    name: "${name} Total Daily Energy"
+    name: Total Daily Energy
     power_id: w_sensor
     filters:
       - multiply: 0.001
     unit_of_measurement: kWh
 
   - platform: template
-    name: "${name} Power Factor"
+    name: Power Factor
     device_class: power_factor
     id: power_factor
     lambda: return id(w_sensor).state / id(v_sensor).state / id(a_sensor).state;
 
 switch:
   - platform: template
-    name: "${name} Relay"
+    name: Relay
     optimistic: true
     id: relay_1
     turn_off_action:

mcu-rf433.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 

mcu-shed.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 
@@ -13,8 +14,8 @@ esp32:
   board: m5stack-atom
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.11
 
 packages:
   common: !include common/common.yaml
@@ -87,20 +88,20 @@ switch:
       mode: OUTPUT
       inverted: true
   - platform: gpio
-    name: "${name} Socket"
+    name: Socket
     id: socket_relay
     pin:
       pca9554: pca9554_module
       number: 4
       mode: OUTPUT
   - platform: gpio
-    name: "Garden Light"
+    name: Garden Light
     id: garden_light_relay
     pin:
       number: 22
       mode: OUTPUT
   - platform: gpio
-    name: "${name} Light"
+    name: Light
     id: shed_light_relay
     pin:
       number: 19

mcu-socket-01.yaml

@@ -1,6 +1,5 @@
 substitutions:
   device: socket-01
-  device_id: socket_01
   name: Socket 01
   area: Bedroom
   comment: "${area} | TV Socket"
@@ -9,6 +8,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 
@@ -36,7 +36,7 @@ binary_sensor:
       number: GPIO13
       mode: INPUT_PULLUP
       inverted: yes
-    name: "${name} Button"
+    name: Button
     # filters:
     #   invert:
     on_press:
@@ -65,11 +65,11 @@ output:
 
 light:
   - platform: binary
-    name: "${name} Red LED"
+    name: Red LED
     id: light_red
     output: led_red
   - platform: binary
-    name: "${name} Blue LED"
+    name: Blue LED
     id: light_blue
     output: led_blue
     
@@ -83,21 +83,21 @@ sensor:
     current_resistor: ${current_res}
     voltage_divider: ${voltage_div}
     current:
-      name: "${name} Current"
+      name: Current
       icon: mdi:flash-circle
       accuracy_decimals: 3
     voltage:
-      name: "${name} Voltage"
+      name: Voltage
       icon: mdi:current-ac
     power:
-      name: "${name} Power"
-      id: "${device_id}_power"
+      name: Power
+      id: power
       icon: mdi:flash-outline
     update_interval: 30s
     change_mode_every: 4
   - platform: total_daily_energy
-    name: "${name} Total Daily Power"
-    power_id: "${device_id}_power"
+    name: Total Daily Power"
+    power_id: power
     filters:
         # Multiplication factor from W to kW is 0.001
         - multiply: 0.001
@@ -106,7 +106,7 @@ sensor:
 
 switch:
   - platform: gpio
-    name: "${name} Relay"
+    name: Relay
     # icon: mdi:power-socket-eu
     pin: GPIO15
     id: relay

mcu-socket-02.yaml

@@ -9,6 +9,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 
@@ -36,7 +37,7 @@ binary_sensor:
       number: GPIO13
       mode: INPUT_PULLUP
       inverted: yes
-    name: "${name} Button"
+    name: Button
     # filters:
     #   invert:
     on_press:
@@ -56,11 +57,11 @@ binary_sensor:
 
 light:
   - platform: binary
-    name: "${name} Red LED"
+    name: Red LED
     id: light_red
     output: led_red
   - platform: binary
-    name: "${name} Blue LED"
+    name: Blue LED
     id: light_blue
     output: led_blue
 
@@ -84,21 +85,21 @@ sensor:
     current_resistor: ${current_res}
     voltage_divider: ${voltage_div}
     current:
-      name: "${name} Current"
+      name: Current
       icon: mdi:flash-circle
       accuracy_decimals: 3
     voltage:
-      name: "${name} Voltage"
+      name: Voltage
       icon: mdi:current-ac
     power:
-      name: "${name} Power"
-      id: "${device_id}_power"
+      name: Power
+      id: power
       icon: mdi:flash-outline
     update_interval: 30s
     change_mode_every: 4
   - platform: total_daily_energy
-    name: "${name} Total Daily Power"
-    power_id: "${device_id}_power"
+    name: Total Daily Power
+    power_id: power
     filters:
         # Multiplication factor from W to kW is 0.001
         - multiply: 0.001
@@ -112,7 +113,7 @@ sensor:
 
 switch:
   - platform: gpio
-    name: "${name} Relay"
+    name: Relay
     # icon: mdi:power-socket-eu
     pin: GPIO15
     id: relay

mcu-socket-03.yaml

@@ -1,6 +1,5 @@
 substitutions:
   device: socket-03
-  device_id: socket_03
   name: Socket 03
   area: Bedroom
   comment: "${area} | SPARE Socket"
@@ -16,6 +15,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 esp8266:
@@ -42,7 +42,7 @@ binary_sensor:
       number: GPIO13
       mode: INPUT_PULLUP
       inverted: yes
-    name: "${name} Button"
+    name: Button
     # filters:
     #   invert:
     on_press:
@@ -72,11 +72,11 @@ output:
 
 light:
   - platform: binary
-    name: "${name} Red LED"
+    name: Red LED
     id: light_red
     output: led_red
   - platform: binary
-    name: "${name} Blue LED"
+    name: Blue LED
     id: light_blue
     output: led_blue
     
@@ -90,15 +90,15 @@ sensor:
     current_resistor: ${current_res}
     voltage_divider: ${voltage_div}
     current:
-      name: "${name} Current"
+      name: Current
       icon: mdi:flash-circle
       accuracy_decimals: 3
     voltage:
-      name: "${name} Voltage"
+      name: Voltage
       icon: mdi:current-ac
     power:
-      name: "${name} Power"
-      id: "${device_id}_power"
+      name: Power
+      id: power
       icon: mdi:flash-outline
       on_value_range:
         - above: ${max_power}
@@ -112,14 +112,14 @@ sensor:
                 data_template:
                   message: Switch turned off because power exceeded ${max_power} W
     energy:
-      name: "${name} Energy"
+      name: Energy
       unit_of_measurement: "Wh"
       icon: mdi:flash-outline
     update_interval: 30s
     change_mode_every: 4
   - platform: total_daily_energy
-    name: "${name} Total Daily Power"
-    power_id: "${device_id}_power"
+    name: Total Daily Power
+    power_id: power
     accuracy_decimals: 5
     filters:
         # Multiplication factor from W to kW is 0.001
@@ -129,7 +129,7 @@ sensor:
 
 switch:
   - platform: gpio
-    name: "${name} Relay"
+    name: Relay
     # icon: mdi:power-socket-eu
     pin: GPIO15
     id: relay

mcu-staircase-light.yaml

@@ -1,11 +1,12 @@
 substitutions:
   device: staircase-light
-  name: Staircase Light
+  name: Staircase
   area: Staircase
   comment: "${area} | Light"
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 
@@ -63,7 +64,7 @@ output:
 
 light:
   - platform: binary
-    name: "${name}"
+    name: Light
     id: light_relay
     output: relay
     restore_mode: ALWAYS_ON

mcu-tft.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   platformio_options:
@@ -17,8 +18,8 @@ esp32:
   variant: ESP32C3
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.11
 
 packages:
   common: !include common/common.yaml

mcu-tracker.yaml

@@ -5,7 +5,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
-  friendly_name: mcu-${device}
+  friendly_name: ${device}
   comment: ${comment}
   on_boot:
     # priority: -10
@@ -88,8 +88,8 @@ esp32:
   #   platform_version: 6.5.0
   framework:
     type: esp-idf
-    version: 5.1.2
-    platform_version: 6.5.0
+    version: 5.3.2
+    platform_version: 53.03.11
 
 ## TESTING
 
@@ -117,13 +117,13 @@ i2c:
 
 modem:
   id: atmodem
-  ready: modem_ready
+  # ready: modem_ready
   rx_pin: 26
   tx_pin: 27
   model: SIM7600
   apn: o2internet
-  username: ""
-  password: ""
+  # username: ""
+  # password: ""
   pin_code: ""
   init_at:
     - AT+CGNSSMODE=15,1 # GNSS all navigation systems
@@ -144,40 +144,40 @@ axp192:
 binary_sensor:
   - platform: gpio
     id: modem_dtr
-    # name: "${name} Cellular DTR"
+    # name: Cellular DTR
     pin: 32
   - platform: gpio
     id: modem_ri
-    # name: "${name} Cellular RI"
+    # name: ellular RI
     pin: 33
   - platform: gpio
     id: modem_status
-    # name: "${name} Cellular Status"
+    # name: Cellular Status
     pin: 36
   - platform: template
     id: modem_ready
-    # name: "${name} Cellular Ready"
+    # name: Cellular Ready
 
 sensor:
   
 switch:
   - platform: gpio
     id: modem_powerkey
-    # name: "${name} Cellular PowerKey"
+    # name: Cellular PowerKey
     pin: 4
     # inverted: true
   - platform: gpio
     id: led
-    # name: "${name} LED"
+    # name: LED
     pin: 12
     inverted: true
   - platform: gpio
     id: modem_enable
-    # name: "${name} Cellular Enable"
+    # name: Cellular Enable
     pin: 25
   - platform: axp192
     id: gnss_enable
-    # name: "${name} GNSS Enable"
+    # name: GNSS Enable
     port: LDO3
 
 text_sensor:
@@ -403,30 +403,30 @@ text_sensor:
 # binary_sensor:
 #   - platform: sim7600
 #     registered:
-#       name: "${name} Cellular"
+#       name: Cellular
 #   - platform: gpio
 #     id: modem_status
-#     name: "${name} Cellular Status"
+#     name: Cellular Status
 #     pin: 36
 
 # sensor:
 #   - platform: sim7600
 #     rssi:
-#       name: "${name} Cellular RSSI"
+#       name: Cellular RSSI
 
 # switch:
 #   - platform: gpio
 #     id: modem_powerkey
-#     # name: "${name} Modem Powerkey"
+#     # name: Modem Powerkey
 #     pin: 4
 #   - platform: gpio
 #     id: led
-#     # name: "${name} LED"
+#     # name: LED
 #     pin: 12
 #     inverted: true
 #   - platform: gpio
 #     id: modem_enable
-#     # name: "${name} Modem Enable"
+#     # name: Modem Enable
 #     pin: 25
 #   - platform: axp192
 #     id: gnss_enable
@@ -445,16 +445,16 @@ text_sensor:
 # text_sensor:
 #   - platform: template
 #     id: sms_sender
-#     name: "${name} SMS Sender"
+#     name: SMS Sender
 #   - platform: template
 #     id: sms_message
-#     name: "${name} SMS Message"
+#     name: SMS Message
 #   - platform: template
 #     id: caller_id_text_sensor
-#     name: "${name} Caller ID"
+#     name: Caller ID
 #   - platform: template
 #     id: ussd_message
-#     name: "${name} USSD Code"
+#     name: USSD Code
 #   - platform: serial
 #     uart_id: modem_uart
 #     id: modem_read

mcu-tv-light.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 
@@ -30,7 +31,7 @@ light:
     id: status_led_id
     pin: 5
   - platform: monochromatic
-    name: "${name}"
+    name: Strip
     output: pwm_cold_white
     effects:
       - flicker:

mcu-vehicle-honda-pcx125.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   on_loop:
@@ -37,11 +38,11 @@ esp32:
   framework:
     type: esp-idf
 
-api:
-  reboot_timeout: 0s
+# api:
+#   reboot_timeout: 0s
 
-wifi:
-  reboot_timeout: 0s
+# wifi:
+#   reboot_timeout: 0s
 
 external_components:
   - source: components
@@ -75,12 +76,11 @@ esp32_ble_beacon:
 
 light:
   - platform: esp32_rmt_led_strip
-    name: "${name} LED"
+    name: LED
     id: led
     rgb_order: GRB
     pin: 27
     num_leds: 1
-    rmt_channel: 0
     chipset: ws2812
     restore_mode: ALWAYS_OFF
     effects:

mcu-vehicle-suzuki-dl650.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   on_loop:
@@ -37,17 +38,17 @@ esp32:
   framework:
     type: esp-idf
 
-api:
-  reboot_timeout: 0s
+# api:
+#   reboot_timeout: 0s
 
-wifi:
-  reboot_timeout: 0s
+# wifi:
+#   reboot_timeout: 0s
 
 external_components:
   - source: components
 
 packages:
-   common: !include common/logger.yaml
+  common: !include common/logger.yaml
 #   common: !include common/common.yaml
   
 # debug:
@@ -75,12 +76,11 @@ esp32_ble_beacon:
 
 light:
   - platform: esp32_rmt_led_strip
-    name: "${name} LED"
+    name: LED
     id: led
     rgb_order: GRB
     pin: 27
     num_leds: 1
-    rmt_channel: 0
     chipset: ws2812
     restore_mode: ALWAYS_OFF
     effects:

mcu-vehicle-toyota-auris-ts.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   on_loop:
@@ -36,24 +37,24 @@ esp32:
   board: m5stack-atom
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.11
 
 external_components:
   - source: components
 
 packages:
-  wifi: !include common/wifi.yaml
+  # wifi: !include common/wifi.yaml
   logger: !include common/logger.yaml
   # api: !include common/api.yaml
-  ota: !include common/ota.yaml
+  # ota: !include common/ota.yaml
 #   common: !include common/common.yaml
 
 # api:
 #   reboot_timeout: 0s
 
-wifi:
-  reboot_timeout: 0s
+# wifi:
+#   reboot_timeout: 0s
 
 # debug:
 
@@ -80,12 +81,11 @@ esp32_ble_beacon:
 
 light:
   - platform: esp32_rmt_led_strip
-    name: "${name} LED"
+    name: LED
     id: led
     rgb_order: GRB
     pin: 27
     num_leds: 1
-    rmt_channel: 0
     chipset: ws2812
     restore_mode: ALWAYS_OFF
     effects:

mcu-vehicle-toyota-yaris-cross.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   on_loop:
@@ -37,18 +38,18 @@ esp32:
   framework:
     type: esp-idf
 
-api:
-  reboot_timeout: 0s
+# api:
+#   reboot_timeout: 0s
 
-wifi:
-  reboot_timeout: 0s
+# wifi:
+#   reboot_timeout: 0s
 
 external_components:
   - source: components
 
 packages:
   common: !include common/logger.yaml
-  wifi: !include common/wifi.yaml
+  # wifi: !include common/wifi.yaml
   # common: !include common/common.yaml
   
 # debug:
@@ -76,12 +77,11 @@ esp32_ble_beacon:
 
 light:
   - platform: esp32_rmt_led_strip
-    name: "${name} LED"
+    name: LED
     id: led
     rgb_order: GRB
     pin: 27
     num_leds: 1
-    rmt_channel: 0
     chipset: ws2812
     restore_mode: ALWAYS_OFF
     effects:

mcu-waterproof-socket.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
 
@@ -28,7 +29,7 @@ binary_sensor:
       number: GPIO0
       mode: INPUT
       inverted: True
-    name: "${name} Button"
+    name: Button
     on_press:
       - switch.toggle: relay
 
@@ -46,7 +47,7 @@ output:
 
 switch:
   - platform: gpio
-    name: "${name} Relay"
+    name: Relay
     pin: GPIO12
     id: relay
     on_turn_on:

mcu-well.yaml

@@ -6,6 +6,7 @@ substitutions:
 
 esphome:
   name: mcu-${device}
+  friendly_name: ${name}
   area: ${area}
   comment: ${comment}
   # friendly_name: mcu-well
@@ -26,8 +27,8 @@ esp32:
   board: m5stack-atom
   framework:
     type: esp-idf
-    version: 5.3.1
-    platform_version: 6.9.0
+    version: 5.3.2
+    platform_version: 53.03.11
 
 packages:
   common: !include common/common.yaml